To Next Page
K
kdixonSep 10, 2025
What causes error #012 on zortrax 3D Printers?
- VVanessa HaasSep 10, 2025
Error #012 indicates that the heatbed thermistor has detected too high heatbed temperature. The suggested solution is Heatbed / heatbed cable replacement.
What causes error #012 on zortrax 3D Printers?
Error #012 indicates that the heatbed thermistor has detected too high heatbed temperature. The suggested solution is Heatbed / heatbed cable replacement.
What to do if my zortrax 3D Printer doesn't load material into the extruder?
If your printer isn't loading material, first ensure that the material hasn't run out. If it has, replace the spool and restart the print. Also, check for tangles on the spool or blockages near the material guide inlet; if found, unload the material, cut off the problem area, reload, and restart. Verify the spool is correctly secured on the holder, allowing proper rotation. Ensure the material isn't faulty with swells. Clean the extruder and hotend of any material remains, especially the extruder motor rack and nozzle, using the provided tools. Finally, ensure the material end is cut at a right angle; cutting it at an acute angle can ease loading.
How to fix error #002 SD card reading error on zortrax M300?
Error #002 indicates an issue with the SD card. To resolve this, save the file to the SD card again. If the problem persists, safely remove the card and try using a different one.
What to do if print stopped due to SD card timeout on zortrax 3D Printers?
If your print stopped due to an SD card timeout, it suggests the card is unreadable or damaged. Try saving the file to the SD card again. If that doesn't work, safely remove the card and use a different one.
Why am I getting error #003 file error on my zortrax 3D Printer?
Error #003 indicates the file cannot be read or the SD card is damaged. To fix this, save the file again to the SD card. If the issue continues, safely remove the card and try another one.
How to solve error #101 no models on SD card on zortrax M300?
Error #101 means the SD card is either unreadable/damaged or contains no models. Try saving the file again onto the SD card. If the problem persists, safely remove the card and use another one.
How to fix error #014 heatbed thermistor error on zortrax M300 3D Printers?
Error #014 means there is no signal coming from the heatbed thermistor. The suggested solution is Heatbed / heatbed cable replacement.
What to do when zortrax M300 3D Printers show error #011?
Error #011 means that the thermocouple has detected too high extruder temperature. The suggested solution is Heater and thermocouple / extruder PCB replacement / extruder cable.
How to troubleshoot error #032 on zortrax 3D Printers?
Error #032 indicates a potential issue with the main extruder cable. Check the connection between the extruder and the extruder cable, then restart the printer. The suggested solution is Extruder cable / extruder PCB replacement.
What to do if I get error #034 on my zortrax 3D Printers?
Error #034 indicates a problem with the endstops. Check the endstops for proper connection. The suggested solution is to carry out X/Y axes maintenance.
General| Build Volume | 300 x 300 x 300 mm |
|---|---|
| Filament Diameter | 1.75 mm |
| Nozzle Diameter | 0.4 mm |
| Connectivity | SD Card |
| Operating System | Windows, macOS |
| Software | Z-SUITE |
| Printing Speed | up to 100 mm/s |
| Heated Bed | Yes |
| Nozzle Temperature | up to 290°C |
| Supported File Formats | .stl, .obj, .dxf, .3mf |
| Supported Materials | Z-ULTRAT, Z-HIPS, Z-GLASS, Z-PETG |
| Power Supply | 100-240 V, 50/60 Hz |
