Why is my ZyXEL Communications Network Router network performance so slow?
A data path loop, which occurs when there is more than one path between two networked computers, can cause broadcast storms that severely impact network performance. Ensure there are no loops in your network topology to resolve this issue.
What to do if the LNK/ ACT, 1 G or 1 0 / 1 0 0 LED does not light up on my ZyXEL Communications Network Router?
First, verify that the attached device is turned on and properly connected to your Switch. Then, make sure the network adapters are working on the attached devices. Finally, ensure that you are using the proper network cable type and that its length does not exceed 100 meters.
Why is my ZyXEL Communications Network Router network performance slow when there are too many hubs?
Having too many hubs (or repeaters) between connected computers can increase network collisions and cause other network problems. Remove any unnecessary hubs from your network to improve performance.
Why do non-standard network cables affect my ZyXEL Communications Network Router?
Non-standard cables may increase the number of network collisions and cause other network problems that affect your network performance.
How to fix PW R LED if it does not light up on ZyXEL Communications Network Router?
Check the connections from your Switch to the power source, ensuring you are using the supplied power cord and an appropriate power source, referring to the product specifications. Also, make sure the power source is turned on and that the Switch is receiving sufficient power. If these steps do not resolve the problem, contact your local distributor for assistance.
What to do if LNK/ACT, 1G or 10/100 LED doesn't light up on ZyXEL Communications Network Router?
If the LNK/ACT, 1G, or 10/100 LED on your ZyXEL Communications Network Router doesn't light up when a device is connected, first ensure the connected device is powered on and properly connected to the router. Also, verify that the network adapters on the connected devices are functioning correctly. Finally, confirm that you're using the correct network cable type and that its length doesn't exceed 100 meters.
How to fix PWR LED not lighting up on ZyXEL Communications Network Router?
If the PWR LED on your ZyXEL Communications Network Router isn't lighting up, check the connections from the router to the power source. Ensure you're using the power cord supplied with the router and an appropriate power source, referring to the product specifications. Also, confirm that the power source is turned on and that the router is receiving sufficient power. If these steps don't resolve the issue, contact your local distributor for assistance.
What to do if PoE LED is off on ZyXEL Communications Network Router?
If the PoE LED is off or power isn't being supplied to your PoE-enabled device via the ZyXEL Communications Network Router, check that the power adapter is securely connected to the router (GS1100-8HP or GS1100-10HP) and an appropriate power source. Make sure the power source is on and functioning properly. Also, check that the Ethernet cables are connected properly and that you're using the correct type of Ethernet cable. If the problem persists, contact your local distributor.
What is the maximum cabling length for ZyXEL Communications Network Router?
Ensure that the network cables used with your ZyXEL Communications Network Router do not exceed the 100 meters limit.
What to do if ZyXEL Communications Network Router cables are faulty?
Replace the faulty cables connected to your ZyXEL Communications Network Router with new standard network cables.
General| PoE Ports | 8 |
|---|---|
| PoE Budget | 130 W |
| Switching Capacity | 20 Gbps |
| Forwarding Rate | 14.88 Mpps |
| MAC Address Table | 8K |
| Jumbo Frame | 9KB |
| PoE Standards | IEEE 802.3af/at |
| Storage Temperature | -40°C to 70°C (-40°F to 158°F) |
| Humidity | 10% to 90% (non-condensing) |
| Power Input | 100-240V AC, 50/60Hz |
| Operating Temperature | 0 to 50 °C |
Lists the essential features and specifications of the GS1100 Series switches.
Step-by-step guide for placing the switch on a desk.
Instructions for mounting the switch securely on a wall.
Details on how to mount the switch in a standard EIA rack.
Addresses issues related to power, hardware, and LED indicator statuses.
Explains common problems caused by incorrect network cabling and setup.
To Next Page