3M File Belt Sander - Safety Precautions; 3 M File Belt Contact Arms

3M
1
/8 in. to
3
/4 in. File Belt Sander 5 Revision 022514
Safety Precautions
1. Read all instructions before using this tool. All operators must be fully
trained in its use and aware of these safety rules.
2. The tool RPM should be checked on a regular basis to ensure proper
operating speed.
3. Make sure the tool is disconnected from the air supply.
4. Always wear required safety equipment when using this tool.
5. Always remove the air supply to the tool before tting, adjusting or
removing the abrasive.
6. Always adopt a rm footing and grip and be aware of torque reaction
developed by the tool.
7. Use only 3M approved spare parts.
8. Always ensure the material being worked is firmly fixed to avoid
movement.
9. Check hose and ttings regularly for wear. Do not carry the tool by its
hose; always be careful to prevent the tool from being started when
carrying the tool with the air supply connected.
10. Dust can be highly combustible.
11. If tool is serviced or rebuilt, check to ensure that the maximum tool
RPM is not exceeded and that there is no excessive tool vibration.
12. Do not exceed maximum recommended air pressure. Use safety
equipment as recommended.
13. The tool is not electrically insulated. Do not use where there is a pos-
sibility of contact with live electricity, gas pipes, and/or water pipes.
14. This tool is not protected against hazards inherent in grinding and
cutting operations and no such accessories should ever be attached.
15. Take care to avoid entanglement with the moving parts of the tool
with clothing, ties, hair, cleaning rags or loose hanging objects. If
entangled, stop air supply immediately to avoid contact with moving
tool parts.
16. If the tool appears to malfunction, remove from use immediately and
arrange for service and repair.
17. Immediately release the start handle in the event of any disruption
of pressure; do not attempt to re-start until the disruption has been
corrected.
18. When tool is not in use, store in a clean dry environment free of
debris.
19. Recycle or dispose of tool according to Local, State, and Federal
Regulations.
Figure 1
Closed Loop Pipe System
Sloped in the direction of air flow
Drain Leg
Ball Valve
To Tool Station
Filter
Drain Valve
Regulator
Lubricator
Ball
Valve
Ball Valve
Air Flow
Air Dryer
Air Compressor
and Tank
Air Hose
To Coupler
at or near Tool
3M™ File Belt Contact Arms
3M Contact Arms are perfectly mated for use on the
3M File Belt Sander. Constructed from premium, industrial-quality
materials, their durability and precise construction are the ideal
complement to the performance of the 3M File Belt Sander. The following
chart is a sample of products offered.
See 3M ASD Accessory catalog 61-5002-8098-9 for additional
Accessories.
Description Part Number
Service Tool Kit 30670
Service Tool Kit
1
2
3
4
5 6
7
REVISION RECORD
R DESCRIPTION / DATE
A
RELEASED FOR PRODUCTION
EDS 11-3-09 RAG 11/18/09
B
ITEM 7 XPA2447 WAS NOT ON
EDS 12/21/09 PWH 12/21/09
IT P/N DESCRIPTION QTY.
1 XPA2394 RETAINING COMPOUND 1
2 XPA2240
WHEEL POSITION BLOCK 1
3 XPA2239
SHAFT REMOVAL TOOL 1
4 XPA2238
BEARING REMOVAL TOOL 3/8 ID 1
5 XPA2237
BEARING REMOVAL TOOL 1/4 ID 1
6 XPA2236
BEARING MOUNT TOOL 1
7 XPA2447
BEARING REMOVAL TOOL 5/8 ID 1
XPA2393
P/N
TITLE
DRWN BY / DATE
MATERIAL
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE
PROPERTY OF X'POLE PRECISION TOOLS INC. ANY REPRO-
DUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN
PERMISSION OF X'POLE PRECISION TOOLS INC. IS PROHIBITED.
CKD BY / DATE
ENG APP / DATE
STD TOL
.X +/-
.XX +/-
.XXX +/-
XX/XX +/-
ANGLES +/-
0.1
0.05
NA
NA
0.5°
X'POLE
PRECISION
TOOLS INC.
EDS
11/3/09
RAG
11/18/09
REVISED 05/26/09
SERVICE TOOL KIT
SEE BOM
ITEM DESCRIPTION QTY.
1 RETAINING COMPOUND 1
2 WHEEL POSITION BLOCK 1
3 SHAFT REMOVAL TOOL 1
4 BEARING REMOVAL TOOL
3
/8 in. ID 1
5 BEARING REMOVAL TOOL
1
/4 in. ID 1
6 BEARING MOUNT TOOL 1
7 BEARING TOOL
5
/8 in. ID 1