What does error E1 mean on A.O. Smith AO-WH-SOFT-450T Water Dispenser?
If your A.O. Smith Water Dispenser displays an “E1” error, which means 'Home not found', cycle the power by unplugging the transformer and plugging it back in to restart the search for Home. Also, ensure the controller is pushed all the way onto the cover plate.
What to do if my A.O. Smith AO-WH-SOFT-450T Water Dispenser has excess water in the brine tank?
If there's excess water in the brine tank of your A.O. Smith Water Dispenser, check for a restricted, frozen, or pinched drain line; remove any restrictions, thaw if frozen, or straighten if pinched. Also, inspect the brine line, brine line flow control, or air check/draw tube for blockages; clean the flow control, air check/draw tube, and brine line, removing any sediment from the brine cabinet. A plugged injector assembly can also cause this, so clean or replace the injector, replacing the entire assembly if the throat is removed.
Why is my A.O. Smith Water Dispenser not indicating flow when water is flowing?
If your A.O. Smith Water Dispenser isn't indicating flow even when water is running, first ensure that the Bypass Valve is in the Service position. Also, check that the appliance is plumbed correctly. If those aren't the issue, the sensor may not be receiving a signal from the magnet on the turbine; remove the sensor from the bypass housing and test it with a magnet on either flat side. If flow is indicated during the test, check the turbine; if not, replace the sensor. Finally, a jammed turbine can cause this, so remove the Bypass Valve and clear any debris from the turbine.
Why is there excess water in the brine tank of my A.O. Smith Water Dispenser?
If your A.O. Smith Water Dispenser has excess water in the brine tank, there might be a few reasons. The drain line could be restricted, frozen, or pinched; if so, remove the restriction, thaw the line, or straighten it. Alternatively, the brine line, brine line flow control, or air check/draw tube might be plugged. In this case, clean the flow control, air check/draw tube, and brine line, and remove any sediment from the brine cabinet. Another possible cause is a plugged injector assembly. Try cleaning or replacing the injector. If the throat is removed, replace the entire assembly.
How to fix an A.O. Smith Water Dispenser that stays in regeneration?
If your A.O. Smith Water Dispenser stays in regeneration mode, several issues could be the cause. First, ensure the controller is properly attached by pushing it all the way onto the cover plate. A defective magnet disk could also be the problem, requiring replacement. Additionally, a foreign object in the main control valve can cause this issue; remove any foreign objects from the main control valve. Lastly, a broken valve assembly with the motor running may be the cause, necessitating repair of the valve assembly.
Why does my A.O. Smith AO-WH-SOFT-450T Water Dispenser produce salty water?
Salty water can result from several issues. A plugged injector can cause this, so replace the injector screen, nozzle, and throat. Low water pressure (below 30 psi) can also be a factor. Check for and remove any restrictions in the drain line, flow control, or brine line. Make sure there isn't too much water in the brine cabinet and verify the correct water level relative to the salt setting. Address intermittent pressure drops by installing a check valve on the inlet water line. Clean the brine valve housing if the brine valve drips water back to the brine tank. If 'Home not found', cycle power by unplugging and replugging the transformer. For a 'Motor error', replug all wires in this sequence: motor, sensor, and power cord, then cycle power. For a 'Home offset', cycle power to reset. If ...
General| Brand | A.O. Smith |
|---|---|
| Model | AO-WH-SOFT-450T |
| Category | Water Dispenser |
| Language | English |
Details the regeneration cycles of the water softener, including backwash and rinse steps.
Explains the four distinct cycles involved in water softener regeneration for optimal performance.
Lists all parts included in the water softener box for installation and setup.
Outlines the essential tools required for a basic installation of the water softener.
Guides on how to test water quality for hardness and pH before softener installation.
Covers essential checks for water pressure, temperature, flow rate, drain, and power supply.
Explains different types of iron and their impact on water softening treatment.
Details how to adjust hardness settings based on iron content for accurate softening.
Covers salt level, type recommendations, and use of potassium chloride.
Includes tips on power outages, regeneration scheduling, and sediment filtering.
Highlights important warnings like toxic chemical reactions and annual maintenance.
Explains how to use the bypass valve for maintenance or watering.
Lists recommended installation practices and code compliance for water softeners.
Highlights common mistakes and actions to avoid during water softener installation.
Identifies parts visible on the back of the water softener unit.
Identifies parts visible on the top of the water softener unit.
Initial steps for preparing the softener and its installation location.
Instructions for safely shutting off the water supply before proceeding.
Guidance on connecting the water inlet and outlet lines according to codes.
Details on connecting the overflow drain line to prevent cabinet overfill.
Instructions for connecting the drain line for backwash water removal.
Steps to flush the plumbing system after initial connections.
Procedure to identify and repair any leaks after installation.
Connects the power supply to the water softener controller.
How to configure the water softener's control panel for optimal performance.
Options for setting regeneration type, mode, and alarms.
Instructions for connecting the softener to a Wi-Fi network.
How to manually start regeneration or reset the controller.
Explains the override feature for extended operation without regeneration.
Initial water addition to the brine tank for startup.
Instructions for adding salt to the brine cabinet.
Final steps to put the softener into service after setup.
Addresses causes and solutions for lack of soft water post-regeneration.
Solutions for general issues resulting in no soft water output.
Diagnoses problems when water flow is not indicated correctly.
Solutions for a blank or non-responsive display on the controller.
Troubleshoots issues where the softener remains in regeneration mode.
Addresses causes and fixes for too much water in the brine tank.
Solutions for when the water softener produces salty water.
Explains and resolves various error messages from the controller.
Details the product's efficiency rating according to NSF/ANSI 44.
Lists the substances the softener can reduce and their levels.
Shows the relationship between salt usage and water softening capacity.
Provides data on capacity, hardness, iron reduction, and flow rates.
Details salt usage and regeneration time for different efficiency settings.
Covers controller type, electrical rating, dimensions, and weight.
Details plumbing connections and types of filter media used.
Outlines what parts are covered and for how long.
Lists conditions and damages not covered by the warranty.
Explains how to obtain service and make a warranty claim.
To Next Page
