A&D FX-iWP Series User Manual

Ver.D20191212B
1
N ADENDUM to FX-iN/FX-iWPN Legal For trade（LFT）Approved Models
Purchased FX-iN/FX-iWPN balances are LFT/Legal for Trade. These balances can be set following the
regulations for the US and Canadian markets. However, there are some differences and limitations in
comparison to the standard versions FX-i/FX-iWP balances, as detailed below.
Note: It is fully the responsibility of the purchaser to set up the balances, including calibration and sealing,
in accordance with local weights and measures regulations.
1. Display and key Operation
General Key operation
For the CAL, MODE, SAMPLE, and PRINT keys, please refer to “4. DISPLAY SYMBOLS
AND KEY OPERATION” of the standard instruction manual.
Key Operation for LFT Approved Model
① The ON:OFF key becomes the ON:OFF/ZERO key
When this key is pressed and hold for 2 seconds: The display turns ON/OFF.
When this key is pressed once: The display is zeroed out.
For the other functions of the ON:OFF key mentioned in the general instruction manual, please
use the ON:OFF /ZERO key as the equivalent of the ON:OFF keys in the standard versions.
② The RE-ZERO key in the standard version becomes the TARE key on the legal for
trade version.
When this key is pressed: The Tare value is registered/canceled.
For the other functions of the RE-ZERO key mentioned in the instruction manual,
please use the TARE key.
③ Front label
The front label must be changed in accordance with the selected mode.
(Example: FX120iN)
This is purchasers’ responsibility
or
①
②
③
Default label (e=10d)
Label in the products’ box (e=d)
This document hosted by: www.oldwillknottscales.com

A&D FX-iWP Series Specifications

General

Brand	A&D
Model	FX-iWP Series
Category	Scales
Language	English

Summary

Display and Key Operation

LFT Model Key Operation

Details key functions for LFT models, including ON/OFF/ZERO and TARE keys.

Front Label Requirements

Specifies that the front label must be changed according to the selected mode.

Mode Selection

Mode Selection Switches and Keys

Explains the switches and keys used for selecting operational modes.

Mode Selection Procedure

Outlines the step-by-step process for selecting the balance's operational mode.

Calibration and Sealing

Calibration Procedure

Details the steps for calibrating the balance using external weights.

Sealing LFT Approved Models

Describes the process of sealing the balance after calibration for legal trade.

Function Switch Settings

Explains the settings available for the function switch on LFT models.

Specifications and Function Tables

Function Table Differences

Lists differences and limitations compared to the standard model's function table.

LFT Mode Specifications

Details specifications for LFT modes, including selectable items and units.

e=10d/e=d Specifications

Provides detailed specifications for e=10d and e=d modes, covering minimum display.

Introduction

About This Manual

Outlines the structure and content of the manual.

Key Features

Highlights the main features and capabilities of the balance.

Compliance Information

Unpacking the Balance

Unpacking Procedure

Provides instructions for unpacking and checking the balance components.

Breeze Break Assembly

Guides the user through assembling the breeze break for specific models.

Installing the Balance

Precautions

Before Use Precautions

Lists essential precautions to follow before operating the balance.

During Use Precautions

After Use Precautions

Power Supply Guidelines

Explains correct handling and warm-up procedures for the AC adapter.

Display Symbols and Key Operation

Weighing Units

Available Weighing Units

Lists the various weighing units and modes supported by the balance.

Storing Custom Units or Modes

Weighing Operations

Basic Weighing (Gram Mode)

Details the fundamental steps for performing basic weighing in gram mode.

Counting Mode (PCS)

Percent Mode Operation

Statistical Calculation Mode

Statistical Mode Example Use

Response Adjustment

Calibration

Calibration Mode Overview

Introduces the two modes for balance calibration: external weight and test.

Calibrating with External Weight

Calibration Test Procedure

Function Switch and Initialization

Permit or Inhibit Function Switches

Describes how to use switches to permit or inhibit parameter changes.

Initializing the Balance to Factory Settings

Function Table

Function Table Structure and Keys

Outlines the hierarchical structure of the function table and the keys used to navigate it.

Function Table Display and Keys

Details of Function Table Parameters

Environment and Display Class Details

Data Output Mode Description

Data Format Description

Data Format Examples

Application Function Description

Comparator Function Details

ID Number and GLP Report

Setting the ID Number

Guides on how to set a unique ID number for the balance.

GLP Report Output

Underhook

Programmable Unit

RS-232C Serial Interface

Peripheral Equipment Connection

Connecting to AD-8121B Printer

Explains how to connect and configure the balance with the AD-8121B printer.

Connecting to a Computer

Using Windows Communication Tools (WinCT)

Commands

Command List

Lists the commands available for controlling the balance via serial interface.

Acknowledge and Error Codes

RS-232C Settings

Maintenance

Troubleshooting

Checking Performance and Environment

Guides on diagnosing balance performance issues by checking setup and environment.

Error Codes Explained

Requesting Repair Service

Options

Specifications

External Dimensions

Terms and Index