ABB HT608784 - Tables

Operation Manual / A170-M.. - A175-M..
Tables
© Copyright 2021 ABB. All rights reserved. HZTL4033_EN Revision I November 2021
Tables
Table1: Definition of pictograms ............................... 9
Table2: Personal protective equipment to be worn
at all times ...................................................................... 13
Table3: Personal protective equipment to be worn
specific to the respective task ................................... 13
Table4: Weight of complete turbocharger unit .... 28
Table5: Foot screws, dimension and strength class..
34
Table6: Foot screws, dimension CE......................... 34
Table7: Foot screws, dimension TE ......................... 34
Table8: Foot screws, number of cup springs ........ 34
Table9: Torque-controlled tightening of the pres-
sure screws .................................................................... 37
Table10: Oil pressure range........................................ 41
Table11: Oil temperature at the inlet....................... 42
Table12: Oil temperature at the outlet.................... 42
Table13: Expected replacement intervals............... 52
Table14: Recommended replacement intervals .... 52
Table15: Tightening torque (81272) ......................... 56
Table16: Tightening torque (81273)......................... 56
Table17: Compressor cleaning parameters ........... 59
Table18: Compressor cleaning parameters ........... 62
Table19: Cleaning parameters Wet cleaning of tur-
bine and nozzle ring..................................................... 68
Table20: Malfunctions when starting – Delayed
start-up .......................................................................... 69
Table21: Malfunctions when starting – Vibrations 69
Table22: Malfunctions when starting – Rubbing of
rotating parts................................................................ 69
Table23: Malfunctions during operation – Lubricat-
ing oil pressure too low............................................... 70
Table24: Malfunctions during operation – Drop in
speed .............................................................................. 70
Table25: Malfunctions during operation – Speed in-
creases ........................................................................... 70
Table26: Malfunctions during operation – Exhaust
gas temperature too high ........................................... 71
Table27: Malfunctions during operation – Charge air
pressure too low............................................................. 71
Table28: Malfunctions during operation – Charge air
pressure too high .......................................................... 72
Table29: Surging of the turbocharger...................... 72
Table30: Malfunctions when stopping – Runout
noises............................................................................... 73
Table31: Malfunctions when stopping – Shortened
runout time ..................................................................... 73
Table32: Malfunction, No speed measurement sig-
nal or poor signal amplitude ....................................... 74
Table33: Malfunction, Measured speed too high ... 74
Table34: Malfunction, Measured speed too low .... 74
Table35: Assembly weights ........................................ 77
Table36: Axial clearance A ........................................... 80
Table37: Tightening torque (56014) ......................... 94
Table38: Tightening torque (57005)......................... 95
Table39: Tightening torque (61069) ......................... 97
Table40: Tightening torque (61059 / 42128) .......... 99
Table41: Tightening torque(86505) ....................... 100
Table42: Inner thread size (25008).......................... 101
Table43: Tightening torque (25013)........................ 102
Table44: Tightening torque (61037) ....................... 103
Table45: Tightening torque, nuts that are difficult
to access (61037) ......................................................... 103
Table46: Tightening torque (61090)....................... 103
Table47: Tightening torque (77015)........................ 104
Table48: Tightening torque(72011)........................ 106
Table49: Axial clearance A......................................... 107
Table50: Tightening torque(72027) ....................... 108
Table51: Tightening torque(72027) ........................ 109
Table52: Tightening torque (56014) ........................ 114
Table53: Tightening torque (61009) ........................ 114
Table54: Tightening torques..................................... 116
Table55: Tightening torques 61009......................... 117
Table56: Locking device tightening torque........... 120
Page 145 / 146Page 145 / 146