EasyManuals Logo

ABB HT610930 User Manual

ABB HT610930
196 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #195 background imageLoading...
Page #195 background image
Operation Manual / A150-M56/66/57/67 - A155-M..
 Tables
© Copyright 2021 ABB. All rights reserved. HZTL4032_EN Revision Q January 2021
  Tables
Table1: Definition of pictograms ............................... 9
Table2: Personal protective equipment to be worn
at all times ...................................................................... 14
Table3: Personal protective equipment to be worn
specific to the respective task ................................... 14
Table4: Weight of complete turbocharger unit .... 29
Table5: Fitting the turbocharger, value X, L........... 35
Table6: Torque-controlled tightening of the pres-
sure screws .................................................................... 37
Table7: Lubricating oil pressure at oil inlet before
turbocharger ................................................................. 44
Table8: Lubricating oil temperature at the inlet... 45
Table9: Maximum lubricating oil temperature at the
outlet .............................................................................. 45
Table10: Tightening torque(86505)........................ 49
Table11: Expected replacement intervals ............... 55
Table12: Maintenance table....................................... 58
Table13: Parameters for wet cleaning of com-
pressor ............................................................................ 61
Table14: Turbine wet cleaning, recommended oper-
ating state ..................................................................... 64
Table15: Wet cleaning of turbines, parameters for 1-
nozzle cleaning.............................................................. 65
Table16: Wet cleaning of turbines, parameters for 6-
nozzle cleaning.............................................................. 66
Table17: Value table for soaking................................ 73
Table18: Tightening torque (81152 / 81154)............ 77
Table19: Malfunctions when starting – Delayed
start-up .......................................................................... 78
Table20: Malfunctions when starting – Vibrations 78
Table21: Malfunctions when starting – Rubbing of
rotating parts................................................................ 78
Table22: Malfunctions during operation – Lubricat-
ing oil pressure too low............................................... 79
Table23: Malfunctions during operation – Speed re-
duces............................................................................... 79
Table24: Malfunctions during operation – Speed in-
creases ........................................................................... 79
Table25: Malfunctions during operation – Exhaust
gas temperature too high .......................................... 80
Table26: Malfunctions during operation – Charge air
pressure too low............................................................ 80
Table27: Malfunctions during operation – Charge air
pressure too high .......................................................... 81
Table28: Malfunctions during operation – Engine
performance losses....................................................... 81
Table29: Malfunction – Turbocharger pumping..... 82
Table30: Malfunction – Sporadic surge blows........ 82
Table31: Malfunctions when stopping – Runout
noises............................................................................... 83
Table32: Malfunctions when stopping – Runout time
too short.......................................................................... 83
Table33: Malfunction of the speed measurement
system – No signal or poor signal amplitude .......... 84
Table34: Malfunction of the speed measurement
system – Measured speed too high........................... 84
Table35: Malfunction of the speed measurement
system – Measured speed too low............................. 84
Table36: Swivel lifting eyes......................................... 86
Table37: Press-off screws ........................................... 87
Table38: Dismantling screw ....................................... 87
Table39: Weights of assemblies................................ 92
Table40: Tightening torques...................................... 93
Table41: Tightening torques for insulation............. 94
Table42: 3 press-off screws...................................... 101
Table43: 6 press-off screws ..................................... 102
Table44: Tightening torque (90012-01) ................. 107
Table45: Permissible clearances A and B................ 112
Table46: Nozzle ring compression PD..................... 113
Table47: Tightening torque (90012-01)................... 116
Table48: Tightening torque (51007) ........................ 117
Table49: Tightening torque (79041) ........................ 118
Table50: Tightening torque (72011) ........................ 119
Table51: Permissible clearances N and R ............... 122
Table52: Tightening torque (51009) ....................... 125
Table53: Tightening torque (51009) ....................... 126
Table54: Tightening torque (72051)........................ 128
Page 193 / 194Page 193 / 194

Table of Contents

Other manuals for ABB HT610930

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the ABB HT610930 and is the answer not in the manual?

ABB HT610930 Specifications

General IconGeneral
BrandABB
ModelHT610930
CategoryIndustrial Equipment
LanguageEnglish

Related product manuals