12
Table 9 - V-Drive Center Distances
TA 2115H
Reducer
Position Mounting.
Motor Frame / Motor Shaft Offset Dimensions “A”
56T / A=.78 140T / A=1.22 180T / A=1.37 210T / A=1.55 250T / A=1.56 280T 320T
A
M1 13.6 – 17.2 13.6 – 17.2 14.6 – 18.1 15.3 – 18.9 16.3 – 19.8 ---- ----
M2 16.6 – 20.1 16.6 – 20.1 17.5 – 21.1 18.3 – 21.9 19.2 – 22.8 ---- ----
M3 19.5 – 23.1 19.5 – 23.1 20.5 – 24.1 21.2 – 24.9 22.2 – 25.9 ---- ----
M4 22.5 – 26.2 22.5 – 26.2 23.5 – 27.1 24.2 – 27.9 25.2 – 28.9 ---- ----
B
M1 18.5 – 22.2 18.5 – 22.2 19.5 – 23.2 20.3 – 24.0 21.3 – 25.0 ---- ----
M2 21.6 – 25.3 21.6 – 25.3 22.6 – 26.3 23.3 – 27.0 24.3 – 28.0 ---- ----
M3 24.6 – 28.3 24.6 – 28.3 25.6 – 29.3 26.4 – 30.1 27.4 – 31.1 ---- ----
C
M1 13.6 – 17.2 13.6 – 17.2 14.6 – 18.1 15.3 – 18.9 16.3 – 19.8 ---- ----
M2 16.6 – 20.1 16.6 – 20.1 17.5 – 21.1 18.3 – 21.9 19.2 – 22.8 ---- ----
M3 19.5 – 23.1 19.5 – 23.1 20.5 – 24.1 21.2 – 24.9 22.2 – 25.9 ---- ----
M4 22.5 – 26.2 22.5 – 26.2 23.5 – 27.1 24.2 – 27.9 25.2 – 28.9 ---- ----
D
M1 10.4 – 14.1 10.4 – 14.1 11.4 – 15.1 12.2 – 15.9 13.2 – 16.9 ---- ----
M2 13.5 – 17.2 13.5 – 17.2 14.5 – 18.2 15.3 – 19.0 16.3 – 20.0 ---- ----
M3 16.6 – 20.3 16.6 – 20.3 17.6 – 21.3 18.3 – 22.0 22.0 – 23.0 ---- ----
TA3203H
Reducer
Position Mounting.
Motor Frame / Motor Shaft Offset Dimension “A”
140T / A=1.22 180T / A=1.37 210T / A=1.55 250T / A=1.56 280T / A=1.16 320T 360T
A
M1 14.6 – 18.4 15.5 – 19.4 16.2 – 20.1 17.2 – 21.1 17.9 – 21.8 ---- ----
M2 17.9 – 21.8 18.9 – 22.8 19.6 – 23.5 20.5 – 24.5 21.3 – 25.2 ---- ----
M3 21.2 – 25.2 22.2 – 26.2 22.9 – 26.9 23.9 – 27.9 24.7 – 28.6 ---- ----
M4 24.6 – 28.6 25.6 – 29.6 26.3 – 30.3 27.3 – 31.3 28.1 – 32.1 ---- ----
B
M1 19.8 – 23.9 20.8 – 24.9 21.6 – 25.6 22.6 – 26.6 23.3 – 27.4 ---- ----
M2 23.3 – 27.3 24.3 – 28.3 25.0 – 29.1 26.0 – 30.1 26.8 – 30.8 ---- ----
M3 26.7 – 30.8 27.7 – 31.8 28.5 – 32.5 29.5 – 33.5 30.2 – 34.3 ---- ----
C
M1 13.6 – 17.4 14.5 – 18.4 15.2 – 19.1 16.2 – 20.1 16.9 – 20.8 ---- ----
M2 16.9 – 20.8 17.8 – 21.7 18.6 – 22.5 19.5 – 23.5 20.2 – 24.2 ---- ----
M3 20.2 – 24.2 21.2 – 25.1 21.9 – 25.9 22.9 – 26.9 23.6 – 27.6 ---- ----
M4 23.6 – 27.6 24.6 – 28.5 25.3 – 29.3 26.3 – 30.3 27.0 – 31.0 ---- ----
D
M1 10.2 – 14.2 11.2 – 15.2 11.9 – 16.0 12.9 – 17.0 13.7 – 17.7 ---- ----
M2 13.6 – 17.7 14.6 – 18.7 15.4 – 19.4 16.4 – 20.4 17.1 – 21.2 ---- ----
M3 17.1 – 21.1 18.1 – 22.1 18.8 – 22.9 19.8 – 23.9 20.6 – 24.6 ---- ----
TA4207H
Reducer
Position Mounting.
Motor Frame / Motor Shaft Offset Dimension “A”
140T / A=1.22 180T / A=1.37 210T / A=1.55 250T / A=1.56 280T / A=1.16 320T / A=.38 360T
A
M1 17.3 – 21.1 18.3 – 22.1 19.0 – 22.8 19.9 – 23.8 20.6 – 24.5 21.6 – 25.5 ----
M2 21.2 – 25.1 22.2 – 26.1 22.9 – 26.8 23.9 – 27.8 24.6 – 28.6 25.6 – 29.5 ----
M3 25.2 – 29.2 26.2 – 30.2 26.9 – 30.9 27.9 – 31.9 28.7 – 32.6 29.6 – 33.6 ----
M4 29.3 – 33.2 30.2 – 34.2 31.0 – 34.9 32.0 – 35.9 32.7 – 36.7 33.7 – 37.7 ----
B
M1 22.6 – 26.7 23.6 – 27.7 24.4 – 28.4 25.4 – 29.4 26.1 – 30.2 27.1 – 31.2 ----
M2 26.8 – 30.8 27.8 – 31.8 28.5 – 32.5 29.5 – 33.5 30.3 – 34.3 31.3 – 35.3 ----
M3 30.9 – 34.9 31.9 – 35.9 32.6 – 36.7 33.6 – 37.7 34.4 – 38.4 35.4 – 39.4 ----
C
M1 15.4 – 19.2 16.3 – 20.1 17.0 – 20.8 18.0 – 21.8 18.7 – 22.5 19.6 – 23.5 ----
M2 19.3 – 23.1 20.2 – 24.1 20.9 – 24.8 21.9 – 25.8 22.6 – 26.5 23.6 – 27.5 ----
M3 23.2 – 27.2 24.2 – 28.1 24.9 – 28.9 25.9 – 29.9 26.6 – 30.6 27.6 – 31.6 ----
M4 27.3 – 31.2 28.2 – 32.2 29.0 – 32.9 29.9 – 33.9 30.7 – 34.6 31.7 – 35.6 ----
D
M1 12.2 – 16.2 13.2 – 17.2 14.0 – 18.0 15.0 – 19.0 15.7 – 19.7 16.7 – 20.7 ----
M2 16.3 – 20.4 17.3 – 21.4 18.1 – 22.1 19.1 – 23.1 19.8 – 23.9 20.8 – 24.9 ----
M3 20.4 – 24.5 21.4 – 25.5 22.2 – 26.2 23.2 – 27.2 23.9 – 28.0 24.9 – 29.0 ----
To Next Page
Loading...
