13
Table 9 - V-Drive Center Distances
TA5215H
Reducer
Position Mounting.
Motor Frame / Motor Shaft Offset Dimension “A”
180T / A=1.37 210T / A=1.55 250T / A=1.56 280T / A=1.16 320T / A=.38 360T / A=1.01 400T
A
M1 19.5 – 23.4 20.2 – 24.1 21.1 – 25.1 21.8 – 25.8 22.8 – 26.8 23.8 – 27.8 ----
M2 24.2 – 28.3 25.0 – 29.0 25.9 – 30.0 26.7 – 30.7 27.6 – 31.7 28.6 – 32.7 ----
M3 29.1 – 33.2 29.8 – 33.9 30.8 – 34.9 31.5 – 35.6 32.5 – 36.6 33.5 – 37.6 ----
M4 34.0 – 38.1 34.7 – 38.8 35.7 – 39.8 36.5 – 40.6 37.4 – 41.5 38.4 – 42.5 ----
B
M1 26.2 – 30.3 26.9 – 31.1 27.9 – 32.1 28.7 – 32.8 29.7 – 33.8 30.7 – 34.8 ----
M2 31.2 – 35.3 31.9 – 36.1 32.9 – 37.1 33.7 – 37.8 34.7 – 38.8 35.7 – 39.8 ----
M3 36.2 – 40.3 36.9 – 41.1 37.9 – 42.1 38.7 – 42.8 39.7 – 43.8 40.7 – 44.8 ----
C
M1 16.4 – 20.3 17.1 – 21.0 18.0 – 21.9 18.7 – 22.6 19.7 – 23.6 20.6 – 24.6 ----
M2 21.1 – 25.1 21.8 – 25.8 22.8 – 26.8 23.5 – 27.5 24.4 – 28.5 25.4 – 29.4 ----
M3 25.9 – 29.9 26.6 – 30.7 27.6 – 31.6 28.3 – 32.4 29.3 – 33.4 30.3 – 34.3 ----
M4 30.8 – 34.8 31.5 – 35.6 32.5 – 36.6 32.2 – 37.3 34.2 – 38.3 35.2 – 39.3 ----
D
M1 17.7 – 21.8 18.4 – 22.6 19.4 – 23.6 20.2 – 24.3 21.2 – 25.3 22.2 – 26.3 ----
M2 22.7 – 26.8 23.4 – 27.6 24.4 – 28.6 25.2 – 29.3 26.2 – 30.3 27.2 – 31.3 ----
M3 N/A N/A N/A N/A N/A N/A ----
TA6307H
Reducer
Position Mounting.
Motor Frame / Motor Shaft Offset Dimension “A”
180T / A=1.37 210T / A=1.55 250T / A=1.56 280T / A=1.16 320T / A=.38 360T / A=1.01 400T / A=.75
A
M1 21.2 – 25.0 21.9 – 25.8 22.9 – 26.7 23.6 – 27.4 24.5 – 28.4 25.5 – 29.4 26.5 – 30.4
M2 26.2 – 30.1 26.9 – 30.8 27.9 – 31.8 28.6 – 32.5 29.6 – 33.5 30.5 – 34.5 31.5 – 35.4
M3 31.2 – 35.1 32.0 – 35.9 32.9 – 36.9 33.7 – 37.6 34.6 – 38.6 35.6 – 39.6 36.6 – 40.6
M4 36.3 – 40.3 37.0 – 41.0 38.0 – 42.0 38.8 – 42.7 39.7 – 43.7 40.7 – 44.7 41.7 – 45.7
B
M1 27.5 – 31.5 28.2 – 32.3 29.2 – 33.3 30.0 – 34.0 31.0 – 35.0 32.0 – 36.0 33.0 – 37.0
M2 32.7 – 36.7 33.4 – 37.5 34.4 – 38.5 35.2 – 39.2 36.2 – 40.2 37.2 – 41.2 38.2 – 42.2
M3 37.9 – 41.9 38.6 – 42.7 39.6 – 43.7 40.4 – 44.4 41.4 – 45.4 42.4 – 46.4 43.4 – 47.4
C
M1 17.9 – 21.6 18.6 – 22.3 19.5 – 23.3 20.2 – 24.0 21.1 – 25.0 22.1 – 25.9 23.0 – 26.9
M2 22.8 – 26.6 23.5 – 27.3 24.4 – 28.3 25.2 – 29.0 26.1 – 30.0 27.1 – 31.0 28.0 – 32.0
M3 27.8 – 31.7 28.5 – 32.4 29.5 – 33.4 30.2 – 34.1 31.2 – 35.1 32.1 – 36.1 33.1 – 37.1
M4 32.8 – 36.8 33.5 – 37.5 34.5 – 38.5 35.3 – 39.2 36.2 – 40.2 37.2 – 41.2 38.2 – 42.2
D
M1 14.4 – 18.4 15.2 – 19.2 16.1 – 20.2 16.9 – 20.9 17.9 – 21.9 18.9 – 22.9 19.9 – 23.9
M2 19.6 – 23.6 20.3 – 24.3 21.3 – 25.3 22.1 – 26.1 23.1 – 27.1 24.1 – 28.1 25.1 – 29.1
M3 24.8 – 28.8 25.5 – 29.5 26.5 – 30.5 27.3 – 31.3 28.3 – 32.3 29.3 – 33.3 30.2 – 34.3
TA7315H
Reducer
Position Mounting.
Motor Frame / Motor Shaft Offset Dimension “A”
210T / A=1.55 250T / A=1.56 280T / A=1.16 320T / A=.38 360T / A=1.01 400T / A=.75 440T
A
M1 27.4 – 31.4 28.4 – 32.4 29.1 – 33.1 30.1 – 34.1 31.1 – 35.1 32.1 – 36.1 ----
M2 33.3 – 37.3 34.3 – 38.3 35.0 – 39.0 36.0 – 40.0 37.0 – 41.0 38.0 – 42.0 ----
M3 39.2 – 43.2 40.2 – 44.2 41.0 – 45.0 42.0 – 46.0 43.0 – 47.0 44.0 – 48.0 ----
M4 45.2 – 49.2 46.2 – 50.2 46.9 – 50.9 47.9 – 51.9 48.9 – 52.9 49.9 – 53.9 ----
B
M1 30.0 – 34.0 31.0 – 35.0 31.8 – 35.7 32.8 – 36.7 33.7 – 37.7 34.7 – 38.7 ----
M2 36.0 – 40.0 37.0 – 40.9 37.7 – 41.7 38.7 – 42.7 39.7 – 43.7 40.7 – 44.7 ----
M3 41.9 – 45.9 42.9 – 46.9 43.6 – 47.6 44.6 – 48.6 45.6 – 49.6 46.6 – 50.6 ----
C
M1 17.4 – 21.3 18.4 – 22.4 19.1 – 23.0 20.0 – 23.9 21.0 – 24.9 22.0 – 25.9 ----
M2 23.2 – 27.1 24.2 – 28.1 24.9 – 28.8 25.9 – 29.8 26.9 – 30.8 27.8 – 31.8 ----
M3 29.1 – 33.0 30.0 – 34.0 30.8 – 34.7 31.8 – 35.7 32.8 – 36.7 33.7 – 37.7 ----
M4 35.0 – 39.0 36.0 – 39.9 36.7 – 40.7 37.7 – 41.7 38.7 – 42.7 39.7 – 43.7 ----
D
M1 20.5 – 24.4 21.5 – 25.4 22.2 – 26.1 23.2 – 27.1 24.2 – 28.1 25.1 – 29.1 ----
M2 26.4 – 30.3 27.4 – 31.3 28.1 – 32.0 29.1 – 33.0 30.1 – 34.0 31.0 – 35.0 ----
M3 32.3 – 36.3 33.3 – 37.2 34.0 – 38.0 35.0 – 39.0 36.0 – 40.0 37.0 – 41.0 ----
To Next Page
Loading...
