①
Power at on with Meter OFF
"Meter Off"で電源をｵﾝ
It becomes all displays while pushing Hold Time.
Hold Timeを押している間､全点灯(図１)
Meter Off
A display shows the total aging time.
表示は通電時間の合計を表示します
Meter:Bar
A display shows a soft version date
ｿﾌﾄの作成日を表示
－12－
A setup of a simultaneous display (Fig.5)
SettheMeterswto10or100or1000W
andpushHoldTimeon5seconds.
同時表示の設定(図5)
Meter:10W/100W/1000W位置+Hold Time5秒押し
"Meter:Off"
Power Supply Switch is turned on with Meter switch in OFF
position, it becomes Adjustment Mode if Hold Time switch
is pushed on 8 times or more before an output relay turns on.
"Meter:Off"で電源をｵﾝ､出力ﾘﾚｨがｵﾝする前に
"
Hold
Time" を8回以上押すと図２の調製ﾓｰﾄﾞになります。
"Meter:Bar"
Fig.1
②
Hold Time is pushed on 8 times or more within a muting time.
ﾐｭｰﾃｨﾝｸﾞ時間内にHoldTimeｽｲｯﾁを8回以上押す｡
(The example of Fig.2 shows 19 hours,45 minutes, 8 seconds)
(図２例；19時間45分8秒)
Fig.2
Fig.3
Fig.4
(The example of fig3 shows April 21, 2004)
(図３例；2004年4月21日)
"50W" for confirmation, see Sterp 2 and 3 of Meter
Calibration of page 11.
A display shows "50W" and returns to soft version date.
Notes ;Please do not change a signal during confirmation.
Calibration will be stopped if Hold Time is pushed
during a check.
50W表示の確認 / 11ﾍﾟｰｼﾞﾒｰﾀ調整ｽﾃｯﾌﾟ2,3を参照｡
50Wを表示し終了すると"ｿﾌﾄ作成日"表示に戻ります。
注意:校正中は信号を変化させないで下さい
校正中(4秒位)にHold Timeを押すと校正を中止
" Meter:Bar"
＋
"HoldTime"ispushed5secormore.
"Meter:Bar"＋"Hold Time"5秒押し"
Digital meter and the bar graph meter are
indicated by simultaneous.
Or a simultaneous display is canceled.
ﾃﾞｨｼﾞﾀﾙﾒｰﾀとﾊﾞｰｸﾞﾗﾌﾒｰﾀを同時表示させる｡
又は同時表示を解除する｡
Release
The above-mentioned operation is repeated.
P
ushHoldTimeon5sec.ormore.
解除
上記動作繰り返す(Hold Timeを5秒押す)
Meter;
10/100/1000W
Hold Time is pushed on 5 seconds.
HoldTimeｽｲｯﾁを5秒押す｡
Fig.5
Fig.6
Shown only
bar graph.
図はﾊﾞｰｸﾞﾗﾌの
みの表示｡
②Push INPUT switch
on 5 seconds
INPUTｽｲｯﾁを5秒押す
A-class :Bias current is restricted to one half.
Aｸﾗｽ：無信号電流を1/2に制限する
Fig.7
①Gain:"-12dB"
P
ush Hold Time on 5 seconds
HOLD TIMEを5秒押す
Normal Operation shown "A-60"
通常状態："A-60"を表示
LED is turned on
at power supply ON.
LED
は電源ｵﾝ時
点灯する｡
Bias half operation from normal operation.
通常動作から無信号を1/2にする
Fig.8
※When an INPUT switch is again pushed
for
5
seconds, it is the A-60 display
of normal operation.
再度INPUTｽｲｯﾁを5秒押すと通常動作のA-60表示
Half Bias Operation
shown "A-
30"
無信号1/2設定：
"A-30"を表示
LED blinks at
power supply ON.
LEDは電源ｵﾝ時
点滅する｡
To Next Page
Loading...
