Why is Acer H5380BD Projector image too small or too large?
Adjust the zoom lever on the top of the projector. Alternatively, move the projector closer to or further from the screen. You can also press "MENU" on the remote control, navigate to "Image - -> Aspect Ratio," and experiment with different settings, or press "Aspect Ratio" on the remote control to adjust directly.
How to fix Acer Projector when no image appears on screen?
First, ensure the projector is connected as described in the "Getting Started" section, and that none of the connector pins are bent or broken. Then, check if the projector lamp has been securely installed, referring to the "Replacing the Lamp" section for guidance. Finally, make sure you have removed the lens cap and that the projector is switched on.
What to do if Acer H5380BD image is out of focus?
First, ensure that the lens cap is removed. Then, adjust the focus ring on the projector lens. Also, make sure the projection screen is within the required distance: 3.9 to 39.0 feet (1.2 to 11.9 meters) for SVGA/XGA series, 3.3 to 32.9 feet (1.0 to 10.0 meters) for WXGA series, 3.3 to 33.8 feet (1.0 to 10.3 meters) for 720p series, or 4.9 to 32.9 feet (1.5 to 10.0 meters) for 1080p series. See the "How to Get a Preferred Image Size by Adjusting Distance and Zoom" section for more details.
How to fix partial or scrolling image on Acer Projector (for notebooks)?
First, press "RESYNC" on the remote control or control panel. If the image is incorrectly displayed, adjust your computer's resolution. Press the toggle output settings. Examples: [Fn]+[F4], Compaq [Fn]+[F4], Dell [Fn]+[F8], Gateway [Fn]+[F4], IBM [Fn]+[F7], HP [Fn]+[F4], NEC [Fn]+[F3], Toshiba [Fn]+[F5]. If you still have difficulty changing resolutions or your monitor freezes, restart all equipment, including the projector.
Why is Acer Projector image stretched when displaying a widescreen DVD?
When playing a DVD encoded in anamorphic or 16:9 aspect ratio, you may need to adjust settings. If playing a 4:3 format DVD, change the format to 4:3 in the projector OSD. If the image is still stretched, adjust the aspect ratio to 16:9 (wide) on your DVD player. If playing a Letterbox (LBX) format DVD, change the format to Letterbox (LBX) in the projector OSD.
What to do if Acer H5380BD Projector image has slanted sides?
If possible, reposition the projector so that it is centered on the screen. You can also press the "Keystone / " button on the remote control until the sides are vertical. If the "Keystone" button is unavailable on the remote control, press "MENU" on the remote, go to "Image - -> Auto Keystone," and choose "Off" on the OSD.
Why is the screen of my notebook computer not displaying my presentation on Acer Projector?
If you're using a Microsoft® Windows® based notebook, it might deactivate its own screen when a second display device is in use. Refer to your computer's manual for reactivation instructions. If you're using an Apple® Mac® OS based notebook, open Display in System Preferences and select Video Mirroring "On".
How to fix unstable or flickering image on Acer Projector?
Adjust the "Tracking" to correct the unstable or flickering image. Also, try changing the display color depth settings on your computer.
How to fix vertical flickering bar on Acer H5380BD image?
Use the "Frequency" setting to make an adjustment. Additionally, check and reconfigure the display mode of your graphics card to ensure it is compatible with the projector.
What to do if Acer Projector stops responding to controls?
If possible, turn off the projector, then unplug the power cord and wait at least 30 seconds before reconnecting power.
Safety precautions regarding power plug disconnection and equipment accessibility.
Instructions for when to refer servicing to qualified personnel.
Important safety advice for projector operation and placement.
Important usage guidelines for the projector, including do's and don'ts.
Key precautions to maximize the life and safe operation of the unit.
Overview of the projector's key technologies and capabilities.
Visual identification of projector parts from front/upper and right/rear sides.
Diagram and steps for connecting the projector with Type 1 setup.
Step-by-step guide for powering on the projector and connecting sources.
Using elevator feet and tilt adjusting wheels to adjust image height and angle.
Accessing and navigating the OSD installation menu for setup and maintenance.
Configuring projection method, mode, and location (front/rear, ceiling).
Selecting desired aspect ratio for optimal display (Auto, Full, 4:3, 16:9, L.Box).
Automatic adjustment for vertical image distortion.
Manual adjustment for image distortion caused by tilting.
Adjusting the sharpness of the projected image.
Selecting or customizing the projector's startup screen.
Capturing an image to use as a custom startup screen.
Configuring how the projector searches for input signals when one is lost.
Enabling or disabling closed captioning for composite/S-Video inputs.
Enabling VGA output connection even when the projector is in standby.
Restoring projector settings to factory defaults.
Setting up user passwords and administrator passwords for projector access.
Enabling ECO mode for lower power consumption and extended lamp life.
Activating high altitude mode for proper cooling in elevated environments.
Selecting between Instant Off, Instant Resume, and Standard shutdown.
Setting an automatic shutdown timer when no signal is detected.
Displaying the projector's elapsed lamp operating time.
Activating a reminder for lamp replacement before end-of-life.
Resetting the lamp hour counter after replacing the lamp module.
Guide to resolving common image problems with solutions.
List of supported resolutions and frequencies for VGA analog PC signals.
Information regarding FCC compliance, interference, and user corrective measures.
Requirement to use shielded cables for peripheral connections.
Guidance on using certified peripherals to maintain FCC compliance.
Warning against unauthorized modifications that could void user authority.
Conditions for FCC compliance: no harmful interference and acceptance of received interference.
Compliance statement for Canadian ICES-003 standards.
General| Number of colors | 1.073 billion colors |
|---|---|
| Native aspect ratio | 16:9 |
| Projection distance | 1 - 10.3 m |
| Vertical scan range | 50 - 120 Hz |
| Horizontal scan range | 30 - 100 kHz |
| Projection technology | DLP |
| Supported aspect ratios | 4:3 |
| Contrast ratio (typical) | 17000:1 |
| Screen size compatibility | 27 - 300 \ |
| Projector native resolution | WXGA (1280x720) |
| Keystone correction, vertical | -40/+40 ° |
| Throw ratio | 1.55 - 1.7:1 |
| Digital zoom | 2 x |
| Optical zoom | 1.1 x |
| Focal length range | 21.86 - 24 mm |
| Aperture range (F-F) | 2.5 - 2.67 |
| Lamp type | OSRAM |
| Lamp power | 190 W |
| Light source type | Lamp |
| Service life of light source | 5000 h |
| Service life of light source (economic mode) | 6000 h |
| Full HD | No |
| HD-Ready | Yes |
| Analog signal format system | NTSC, PAL, SECAM |
| Composite video in | 0 |
| USB connector type | Mini-USB B |
| Serial interface type | RS-232 |
| USB 2.0 ports quantity | USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them. |
| Noise level | 31 dB |
| Noise level (economic mode) | 28 dB |
| RMS rated power | 2 W |
| Placement | Ceiling |
| Product type | Standard throw projector |
| Product color | White |
| Market positioning | Home cinema |
| Power source | AC |
| AC input voltage | 110 - 220 V |
| Power consumption (standby) | 0.5 W |
| Power consumption (typical) | 235 W |
Weight and Dimensions| Depth | 223 mm |
|---|---|
| Width | 314 mm |
| Height | 93 mm |
| Weight | 2500 g |
To Next Page
