Why does Acer Projector lamp burn out?
When the lamp in your Acer Projector reaches the end of its useful life, it will burn out and may make a loud popping sound. If this happens, the projector will not turn on until the lamp module has been replaced. To replace the lamp, follow the procedures in the "Replacing the Lamp" section.
What to do if Acer P1183 stops responding?
If the projector stops responding to all controls, turn off the Acer Projector, unplug the power cord, and wait at least 30 seconds before reconnecting the power.
What to do if notebook computer is not displaying presentation on Acer P1183 Projector?
If the screen of your notebook computer isn't displaying your presentation on the Acer Projector, and you're using a Microsoft® Windows® based notebook, it might be deactivating its own screen. Consult your computer's manual for reactivation instructions. If you're using an Apple® Mac® OS based notebook, go to System Preferences, open Display, and select Video Mirroring "On".
How to troubleshoot no image on Acer P1183?
If your Acer Projector is not displaying any image onscreen, ensure it's connected as described in the "Getting Started" section. Check that none of the connector pins are bent or broken. Verify the projector lamp is securely installed, referring to the "Replacing the Lamp" section if needed. Also, confirm that you've removed the lens cap and the projector is switched on.
How to fix out of focus image on Acer P1183?
If your Acer Projector's image is out of focus, first ensure the lens cap is removed. Then, adjust the focus ring on the projector lens. Also, verify that the projection screen is within the required distance, which varies depending on your projector series: 3.9 to 39.0 feet for SVGA/XGA, 3.3 to 32.9 feet for WXGA, 3.3 to 33.8 feet for 720p, or 4.9 to 32.2 feet for 1080p series.
How to fix partial or scrolling image on Acer P1183 Projector (for PC)?
Try pressing "RESYNC" on the remote control or control panel. If the image is incorrectly displayed, open "My Computer," then the "Control Panel," and double-click the "Display" icon. Select the "Settings" tab and verify that your display resolution setting is lower than or equal to WUXGA-RB (1920 x 1200). Click the "Advanced Properties" button. If the problem persists, change the monitor display you are using and follow these steps: Verify that the resolution setting is lower than or equal to WUXGA-RB (1920 x 1200). Click the "Change" button under the "Monitor" tab. Click "Show all devices". Next, select "Standard monitor types" under the SP box, and choose the resolution mode you need under the "Models" box. Verify that the resolution setting of the monitor display is lower than or equal...
How to fix no image on Acer P1183 Projector?
If no image appears on your Acer Projector, ensure that all connections are correctly set up as described in the "Getting Started" section, and that none of the connector pins are bent or broken. Verify that the projector lamp is securely installed. Also, remember to remove the lens cap and switch on the projector.
Why is my Acer P1183 image out of focus?
If your Acer Projector displays an image that is out of focus, first ensure that the lens cap has been removed. Then, adjust the focus ring on the projector lens. Also, make sure the projection screen is within the required distance: 3.9 to 39.0 feet (1.2 to 11.9 meters) for SVGA/XGA series, 3.3 to 32.9 feet (1.0 to 10.0 meters) for WXGA series, 3.3 to 33.8 feet (1.0 to 10.3 meters) for 720p series, or 4.9 to 32.2 feet (1.5 to 9.8 meters) for 1080p series.
Why is the screen of my notebook computer not displaying my presentation on Acer P1183 Projector?
If you're using a Microsoft® Windows® based notebook, it might deactivate its own screen when a second display device is in use. Refer to your computer's manual for reactivation instructions. If you're using an Apple® Mac® OS based notebook, open Display in System Preferences and select Video Mirroring "On".
Why is Acer P1183 Projector image stretched when displaying a widescreen DVD?
When playing a DVD encoded in anamorphic or 16:9 aspect ratio, you may need to adjust settings. If playing a 4:3 format DVD, change the format to 4:3 in the projector OSD. If the image is still stretched, adjust the aspect ratio to 16:9 (wide) on your DVD player. If playing a Letterbox (LBX) format DVD, change the format to Letterbox (LBX) in the projector OSD.
General| Aspect Ratio | 4:3 (Native), 16:9 (Supported) |
|---|---|
| Display Technology | DLP |
| Audio | 2W Speaker |
| Model | P1183 |
| Lamp Life | 5, 000 Hours (Standard), 6, 000 Hours (ECO) |
| Projection Distance | 1.0 m ~ 10.0 m |
| Throw Ratio | 1.95 ~ 2.15 (50"@2m) |
| Connectivity | HDMI |
| Zoom Ratio | 1.1x |
| Video Compatibility | 480i, 480p, 576i, 576p, 720p, 1080i, 1080p |
| Output Connectors | Analog RGB: D-Sub (15 pin) x 1, PC Audio: Stereo mini jack x 1 |
| Projection Size | 30 - 300 inches |
| Noise Level | 29 dBA (ECO Mode) |
To Next Page
