What to do if my Acer P1165E Projector has no signal?
If your Acer Projector shows no signal, first ensure the source is turned on. If the issue persists, try replacing the cable. If neither of these steps works, the I/O Board or the Optical Engine may need to be replaced.
How to troubleshoot Acer P1165E Projector with no power source?
If your Acer Projector is not turning on, verify the AC socket and connector connection. If that doesn't solve the issue, consider replacing the AC Safety Switch board, power board, keypad, or main board. Also, check the LED and FPC, and the 16 pin Fuse.
Why is my Acer P1165E remote control not working?
If your Acer Projector's remote control isn't working, start by checking the battery level. If the batteries are fine, try replacing the remote control. You may also need to check the IR, or replace the I/O Board or Main board.
What to do if my Acer P1165E Projector fails to light up?
If your Acer Projector fails to light up, start by checking the LED indicator and follow any indicative actions. If the issue continues, consider replacing the Lamp Module, Power board, Ballast, I/O Board, Main board, or Optical Engine.
How to fix image abnormality on Acer Projector?
If the image on your Acer Projector appears abnormal, try powering it on again and resetting the OSD. Additionally, adjust the input cable and signal settings. If problems persist, consider replacing the I/O Board, Main Board, or Optical Engine.
How to troubleshoot color issues on Acer P1165E?
If the color on your Acer Projector appears abnormal, first adjust the input signal. If the issue persists, adjust the Color Wheel Index. If neither of these steps resolves the problem, consider replacing the I/O board, Main Board, or Optical Engine.
What causes button failure on Acer P1165E Projector?
If the buttons on your Acer Projector are not working, check the keypad and FPC. If the problem persists, consider replacing the I/O Board or Main board.
How to fix no volume on Acer Projector?
If there is no volume coming from your Acer Projector, check the keypad and FPC. If the issue persists, try replacing the Speaker, I/O Board, or Main Board.
Lists critical safety measures to be observed during projector maintenance and repair.
Highlights the importance of using exact replacement parts for safety-critical components.
Warns service personnel about specific hazards like UV radiation, high voltage, and hot lamps.
Details the technical specifications, including display type, resolution, and input sources for both models.
Specifies the characteristics and radiated power of the projector lamps for P1165E and P5260E.
Illustrates the system architecture and component interconnections of the projectors.
Lists the necessary tools and equipment required for the firmware upgrade process.
Provides step-by-step instructions for installing DLP Composer and performing the firmware upgrade.
Details the procedure for connecting the projector and PC via USB for firmware updates.
Lists the specialized tools required for the disassembly and replacement of projector parts.
Provides essential warnings and general guidelines for disassembling the projector safely and correctly.
Details the specific steps for safely removing and replacing the projector's lamp module.
Provides instructions for disassembling and removing the main board and the DMD board.
Provides guidance on identifying and troubleshooting common projector problems using indicators and procedures.
Covers specific troubleshooting flows for power, light/sound, video, image, and operation functions.
Describes the tests required to verify the quality and functionality of a repaired projector unit.
Details signal, operation, image quality, resolution, sensor, brightness, safety, and cosmetic tests.
Identifies connectors on the main board and their respective functions.
Details the connectors and interface of the ballast board for the P1165E.
Describes the connectors and pinouts for the projector's power board.
Identifies the connectors on the I/O board and their functions for various input/output interfaces.
Illustrates the mechanical components and their assembly for various parts of the projector.
Lists FRUs by category: Accessories, Boards/Modules, Cases/Covers, Fans, Optical Devices, Miscellaneous, Wires, and Screws.
General| Number of colors | 16.78 million colors |
|---|---|
| Projection distance | 1 - 12 m |
| Vertical scan range | 56 - 85 Hz |
| Horizontal scan range | 31.5 - 100 kHz |
| Projection technology | DLP |
| Contrast ratio (typical) | 2000:1 |
| Screen size compatibility | 0.58 - 7.62 \ |
| Projector native resolution | SVGA (800x600) |
| Keystone correction, vertical | ±40 ° |
| Digital zoom | 2 x |
| Aspect ratio | 4:3, 16:9 |
| RS-232 ports | 1 |
| Dimensions (WxDxH) | 300 x 228 x 100 mm |
| Lamp type | P-VIP |
| Lamp power | 180 W |
| Light source type | Lamp |
| Service life of light source | 3000 h |
| Serial interface type | RS-232 |
| USB 2.0 ports quantity | USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them. |
| Power consumption (standby) | 5 W |
| Power consumption (typical) | 250 W |
| Market positioning | Presentation |
Weight and Dimensions| Weight | 2800 g |
|---|
To Next Page
