How to fix Acer P1173 with no image on screen?
First, ensure all cables are correctly connected. Check for bent or broken connector pins. Verify the projection lamp is securely installed. Finally, ensure the Acer Projector is switched on.
What to do if Acer P1173 image is too small or too large?
To adjust the image size on your Acer Projector, use the zoom lever on top of the projector. You can also move the projector closer to or further from the screen. Alternatively, press "MENU", go to "Image" > "Aspect Ratio", and try different settings.
What to do if Acer P1173 image is out of focus?
Adjust the focus ring on the projector lens of your Acer Projector. Also, make sure the projection screen is within the required distance of 4.9 to 19.7 feet (1.5 to 6 meters).
How to fix unstable or flickering image on Acer Projector?
Correct the unstable or flickering image on your Acer Projector by using the "Tracking" setting. Also, try changing the display color setting on your computer.
How to fix partial or scrolling image on Acer P1173 (notebooks)?
Press "RESYNC" on the control panel or remote control of your Acer Projector. For an incorrectly displayed image: Adjust the resolution of your computer. Press the toggle output settings. If you experience difficulty changing resolutions or your monitor freezes, restart all equipment including the projector.
Why notebook computer screen is not displaying presentation on Acer P1173 Projector?
If you're using a Microsoft® Windows® based notebook with your Acer Projector: Some notebooks deactivate their screens when a second display is used. Refer to your computer's manual for reactivation instructions. If you're using an Apple® Mac® OS based notebook: Open Display in System Preferences and turn Video Mirroring "On."
Why does Acer P1173 lamp burn out or makes a popping sound?
When the lamp in your Acer Projector reaches the end of its life, it will burn out and may make a loud popping sound. If this occurs, the projector will not turn on until you replace the lamp module.
What to do if Acer P1173 image has slanted sides?
Reposition the Acer Projector so it's centered on the screen and below the bottom edge, if possible. Use the Keystone correction keys on the control panel or remote until the image is square. Alternatively, go to "Image" > "Auto Keystone" or "Image" > "Keystone" in the OSD menu to make adjustments.
How to correct reversed image on Acer P1173 Projector?
To correct a reversed image on your Acer Projector, go to "Image" > "Projection Mode" or "Image" > "Projection Location" in the OSD and adjust the projection direction.
How to fix Acer Projector image with vertical flickering bar?
To fix a vertical flickering bar on your Acer Projector's image, use the "Frequency" setting to make an adjustment. Also, check and reconfigure the display mode of your graphics card to ensure it's compatible with the projector.
General| Number of colors | 1.073 billion colors |
|---|---|
| Native aspect ratio | 4:3 |
| Projection distance | 1 - 11.9 m |
| Vertical scan range | 30 - 100 Hz |
| Horizontal scan range | 50 - 120 kHz |
| Projection technology | DLP |
| Supported aspect ratios | 16:9 |
| Contrast ratio (typical) | 17000:1 |
| Screen size compatibility | 24 - 300 \ |
| Projector native resolution | SVGA (800x600) |
| Keystone correction, vertical | -40/+40 ° |
| Digital zoom | 2 x |
| Focal length range | 21 - 23 mm |
| Aperture range (F-F) | 2.57 - 2.65 |
| Lamp type | P-VIP |
| Lamp power | 190 W |
| Light source type | Lamp |
| Service life of light source | 5000 h |
| Service life of light source (economic mode) | 6000 h |
| 3D | - |
| Full HD | No |
| 3D Ready | Yes |
| Analog signal format system | NTSC, PAL, SECAM |
| Audio (L/R) in | 0 |
| USB connector type | Mini-USB B |
| Serial interface type | RS-232 |
| USB 2.0 ports quantity | USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them. |
| Noise level | 29 dB |
| RMS rated power | 3 W |
| Placement | Desktop |
| Product type | Standard throw projector |
| Product color | White |
| Market positioning | Presentation |
| Power source | AC |
| Power consumption (standby) | - W |
| Power consumption (typical) | 240 W |
Weight and Dimensions| Depth | 220 mm |
|---|---|
| Width | 264 mm |
| Height | 78 mm |
| Weight | 2000 g |
Important safety warnings including avoiding water, unstable surfaces, and blocking vents.
Guidelines for connecting and disconnecting power to the external supply.
Ensuring the power outlet is easily accessible for disconnection.
Instructions for using the projector, including what to do and not to do.
General precautions to maximize the projector's lifespan and ensure safe operation.
Details about the projector's key technologies and capabilities.
Diagrams and labels of the projector's front/upper and rear sides.
Diagram and instructions for connecting the projector to various devices.
Steps and indicators for powering on the projector and source devices.
Procedure for powering down the projector and standby mode indicators.
Using elevator feet to adjust the projector's image height and angle.
Accessing the OSD menu for projector installation and maintenance.
Compliance information for FCC regulations regarding digital devices.
French note for Canadian users regarding Class B digital apparatus.
Acer's declaration of conformity with EU essential requirements and directives.
To Next Page
