What to do if Acer P5330W image freezes displaying photo or document?
If the image hangs up when displaying a photo or document in Media on your Acer Projector, power off the projector and then power it on again.
How to fix vertical flickering bar on Acer P5330W Projector image?
If your Acer Projector image has a vertical flickering bar: * Use "Frequency" to make an adjustment. * Check and reconfigure the display mode of your graphics card to make it compatible with the projector.
How to stabilize flickering image on Acer P5330W?
If the image from your Acer Projector is unstable or flickering: * Adjust the "Tracking" to correct it. * Change the display color depth settings on your computer.
Why is Acer P5330W image partial or scrolling from notebook?
If your Acer Projector displays a partial, scrolling, or incorrectly displayed image from notebooks, follow these steps for an incorrectly displayed image: * Follow the steps for item 2 to adjust the resolution of your computer. * Press the toggle output settings. Example: [Fn]+[F4], Compaq [Fn]+[F4], Dell [Fn]+[F8], Gateway [Fn]+[F4], IBM [Fn]+[F7], HP [Fn]+[F4], NEC [Fn]+[F3], Toshiba [Fn]+[F5] * If you experience difficulty changing resolutions or your monitor freezes, restart all equipment including the projector.
Why is my Acer P5330W Projector image out of focus?
To correct an out-of-focus image on your Acer Projector: * Ensure that the lens cap is removed. * Adjust the focus ring on the projector lens. * Make sure the projection screen is within the required distance of 3.3 to 29.7 feet (1.0 to 9.1 meters) for XGA series / 3.3 to 25.2 feet (1.0 to 7.7 meters) for WXGA series / 3.3 to 24.6 feet (1.0 to 7.5 meters) for 1080p series / 3.3 to 24.0 feet (1.0 to 7.3 meters) for WUXGA series from the projector.
Why does my Acer Projector lamp burn out or pop?
When the lamp reaches the end of its useful life, it will burn out and may make a loud popping sound. If this occurs, the projector will not turn on until the lamp module has been replaced. To replace the lamp, follow the procedures in the "Replacing the Lamp" section.
How to adjust image size on Acer P5330W?
To adjust the image size, try the following: Adjust the zoom ring on the projector; move the projector closer to or further from the screen; or press "MENU" on the remote control, navigate to "Image - -> Aspect Ratio", and experiment with different settings. You can also directly press "RATIO" on the remote control.
Why is Acer P5330W Projector image stretched with widescreen DVD?
When you play a DVD encoded in anamorphic or 16:9 aspect ratio, you may need to adjust the following settings: If you play a 4:3 format DVD title, change the format to 4:3 in the projector OSD. If the image is still stretched, adjust the aspect ratio and set up the display format to 16:9 (wide) aspect ratio on your DVD player. If you play an Letterbox (LBX) format DVD title, change the format to Letterbox (LBX) in the projector OSD.
How to remove vertical flickering bar on Acer P5330W Projector?
Use "Frequency" to make an adjustment; refer to the "Image" section for more details. Also, check and reconfigure the display mode of your graphics card to ensure it is compatible with the projector.
How to stabilize a flickering image on Acer P5330W?
Adjust the "Tracking" to correct the flickering. You can find more information in the "Image" section. Also, try changing the display color depth settings on your computer.
Cautions for power, cleaning, and safe usage environments.
Essential guidelines and warnings for correct and effective projector use.
Highlights the key features and technologies of the DLP projector.
Illustrates and lists connections for setting up the projector.
Step-by-step guide for powering on the projector and connecting a source.
Explains how to adjust projector height using feet and tilt wheel.
Tables for optimizing image size by adjusting distance and zoom.
Guides on using OSD for projector installation and maintenance setup.
Explains navigation and use of OSD menus for adjustments.
Provides solutions for common problems encountered with the projector.
Step-by-step instructions for safely replacing the projector lamp module.
General| Number of colors | 1.073 billion colors |
|---|---|
| Native aspect ratio | 16:10 |
| Projection distance | 1 - 7.7 m |
| Projection technology | DLP |
| Supported aspect ratios | 4:3, 16:10 |
| Contrast ratio (typical) | 20000:1 |
| Screen size compatibility | - \ |
| Projector native resolution | WXGA (1280x800) |
| Vertical synchronization (max) | 0.12 kHz |
| Vertical synchronization (min) | 0.024 kHz |
| Keystone correction, horizontal | -20 - 20 ° |
| Horizontal synchronization (max) | 100 kHz |
| Horizontal synchronization (min) | 15 kHz |
| RMS rated power | 16 W |
| Number of built-in speakers | 1 |
| Lamp type | UHP |
| Lamp power | 240 W |
| Lamps quantity | 1 lamp(s) |
| Light source type | - |
| Service life of light source | - h |
| Throw ratio | 1.19 to 1.54 |
| Focal length range | 16.91 - 21.6 mm |
| Aperture range (F-F) | 2.5 - 2.782 |
| Full HD | No |
| Analog signal format system | NTSC, PAL, SECAM |
| Supported graphics resolutions | 1920 x 1200 (WUXGA) |
| Serial interface type | RJ-45 |
| USB 2.0 ports quantity | USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them. |
| VGA (D-Sub) ports quantity | 3 |
| Component video (YPbPr/YCbCr) in | 0 |
| Noise level | - dB |
| Projection modes | Ceiling, Front, Rear |
| Compatible operating systems | Mac PC Windows PC |
| Placement | Ceiling |
| Product type | Large venue projector |
| Product color | White |
| Power source | AC |
| AC input voltage | 120 - 230 V |
| Power consumption (standby) | - W |
| Power consumption (typical) | 290 W |
| Operating temperature (T-T) | 0 - 40 °C |
| Operating relative humidity (H-H) | 0 - 80 % |
| Harmonized System (HS) code | 85286200 |
Weight and Dimensions| Weight | 2730 g |
|---|
To Next Page
