How to remove vertical flickering bar on Acer P5530?
Use "Frequency" to make an adjustment; refer to the "Image" section for more details. Also, check and reconfigure the display mode of your graphics card to ensure it is compatible with the projector.
How to flip reversed image on Acer P5530?
Select "Image --> Projection Mode" on the OSD and adjust the projection direction.
Why does my Acer Projector lamp burn out or pop?
When the lamp reaches the end of its useful life, it will burn out and may make a loud popping sound. If this occurs, the projector will not turn on until the lamp module has been replaced. To replace the lamp, follow the procedures in the "Replacing the Lamp" section.
General| Placement | Ceiling |
|---|---|
| Product type | Large venue projector |
| Product color | White |
| Market positioning | Presentation |
| Mac compatibility | Yes |
| Number of colors | 1.073 billion colors |
| Native aspect ratio | 16:9 |
| Projection distance | 1 - 7.5 m |
| Projection technology | DLP |
| Supported aspect ratios | 4:3, 16:9 |
| Contrast ratio (typical) | 20000:1 |
| Screen size compatibility | 31 - 300 \ |
| Projector native resolution | 1080p (1920x1080) |
| Vertical synchronization (max) | 0.12 kHz |
| Vertical synchronization (min) | 0.024 kHz |
| Horizontal synchronization (max) | 100 kHz |
| Horizontal synchronization (min) | 15 kHz |
| Projector brightness (economic mode) | 3200 ANSI lumens |
| 3D | - |
| Analog signal format system | NTSC, PAL, SECAM |
| Focus | Manual |
| Throw ratio | 1.13 - 1.47:1 |
| Digital zoom | 2 x |
| Optical zoom | 1.3 x |
| Focal length range | 16.91 - 21.6 mm |
| Aperture range (F-F) | 2.5 - 2.782 |
| Lamp type | UHP |
| Lamp power | 240 W |
| Lamps quantity | 1 lamp(s) |
| Light source type | Lamp |
| Service life of light source | - h |
| RMS rated power | 16 W |
| Number of built-in speakers | 1 |
| Wi-Fi | No |
| USB 2.0 ports quantity | USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them. |
| VGA (D-Sub) ports quantity | 3 |
| Component video (YPbPr/YCbCr) in | 0 |
| Power source | AC |
| AC input voltage | 100 - 240 V |
| Power consumption (standby) | - W |
| Power consumption (typical) | 290 W |
| Power consumption (economy mode) | 205 W |
| Noise level | 31 dB |
| Projection modes | Ceiling, Front, Rear |
| Noise level (economic mode) | 24 dB |
| Harmonized System (HS) code | 85286200 |
Weight and Dimensions| Depth | 214 mm |
|---|---|
| Width | 315 mm |
| Height | 103 mm |
| Weight | 2730 g |
Instructions for safely turning off the projector before cleaning.
Guidelines for connecting and disconnecting the power supply unit.
Advice on power outlet accessibility and safe disconnection.
Important safety precautions regarding water, placement, ventilation, and objects.
Guidelines for operating the projector using electrical power safely.
Explains the grounding pin's safety role and noise protection.
Advises against self-servicing and to contact qualified personnel.
Warning about looking into the projector lens and facing it towards the sun.
Lists unsuitable environments like confined spaces or high temperatures.
What to do if issues arise and how to handle the projector.
Recommendations for proper power cycling and cooling procedures.
Warnings about hot surfaces, lamp replacement, and cooling.
Guidance on projector placement, tilt, and mounting.
Information on lamp life, replacement, and related procedures.
Instructions to protect hearing while using the projector's audio.
Guidance on recycling electronic devices and proper disposal.
Information about mercury content in lamps and disposal requirements.
Warning against staring into the projector's direct beam (RG2).
Do's and Don'ts for projector operation and cleaning.
Recommendations to maximize unit life by following warnings and maintenance.
Critical safety alerts regarding lens use, electrical shock, and lamp handling.
Highlights of the DLP projector's capabilities and technologies like ColorBoost and LumiSense+.
Lists all items included in the projector package, including optional accessories.
Identifies external components on the front and upper side of the projector with labels.
Identifies external connectors and ports on the rear side of the projector.
Step-by-step guide for installing the Acer Wireless Projection Kit.
Describes the buttons on the projector's control panel and their functions.
Details the buttons on the remote control and their operations for projector control.
Explains functions like Freeze, PgUp/PgDn, Media, and Laser Pointer.
Explains MHL control modes and how to navigate them.
Details the functions of remote buttons when using MHL control.
Explains MEDIA, PgUp/PgDn, and KeyPad functions in MHL mode.
Illustrates how to connect various devices to the projector using different cables.
Step-by-step guide to powering on the projector and source devices.
Step-by-step guide for turning off the projector and its cooling cycle.
Explains OSD messages for projector overheating or fan failure.
How to adjust the image height using elevator feet and tilt wheel.
Table and guide for optimizing image size based on distance for XGA series.
Table and guide for optimizing image size based on distance for WXGA series.
Table and guide for optimizing image size based on distance for 1080p series.
Table and guide for optimizing image size based on distance for WUXGA series.
Table showing how to achieve desired image size by adjusting distance and zoom.
Table showing how to achieve desired image size by adjusting distance and zoom.
Table showing how to achieve desired image size by adjusting distance and zoom.
Table showing how to achieve desired image size by adjusting distance and zoom.
Accessing and navigating the projector's installation menu and its options.
How to open, navigate, and use the projector's OSD menus.
Example of OSD menus like Color, showing settings and navigation.
Settings for LumiSense+, BluelightShield, and Dynamic Black.
Controls for Display Mode, Wall Color, Brightness, Contrast, Saturation, and Tint.
Adjusting color temperature, gamma, and individual color gains.
Detailed color adjustments for specific color components and effects like Brilliant Color.
Settings for projection mode, location, and aspect ratio.
Adjusting image distortion using keystone and corner correction.
Adjusting image sharpness and horizontal/vertical position.
Adjusting signal timing (frequency/tracking) and HDMI color/scan info.
Customizing the startup screen and capturing images.
Configuring source detection, USB power, HDMI CEC, and VGA OUT.
Configuring projector security, timeout intervals, and user/administrator passwords.
Setting up network details and resetting the projector to factory defaults.
Managing ECO mode, High Altitude mode, and Auto Shutdown.
Managing control panel locks, lamp hour elapse, and reminders.
Adjusting volume and muting the audio output.
Adjusting volume for power on/off and warning notifications.
Settings for enabling DLP 3D, format, and warning messages.
Notes on graphic card settings, software players, and 3D sync invert.
Choosing the projector's OSD menu language.
How to access and log into the Acer LAN webpage management.
Overview of the web interface home page, showing status and functions.
Using the web interface control panel to adjust projector settings.
Setting IP address, group name, and password via the web interface.
Setting up email alerts for projector problems using SMTP settings.
How to log out of the Acer LAN webpage management.
Solutions for common image display problems like no image or incorrect display.
Solutions for image problems specific to notebooks and image stability/focus.
Solutions for images stretched due to aspect ratio mismatches.
Solutions for images too small/large, slanted sides, or image reversal.
Explains OSD messages related to fan failure, overheating, and lamp life.
Steps for projector unresponsiveness and lamp burnout troubleshooting.
Defines the meaning of different LED states (Lamp, Temp, Power) and alarm conditions.
Step-by-step guide for safely replacing the projector lamp.
Warning about the hot lamp compartment and cooling time before replacement.
Steps for drilling holes and securing the ceiling mount base.
Selecting appropriate pole length combinations for ceiling mounting.
How to attach the projector to the bracket and maintain heat distribution space.
Adjusting angle/position and specifications for mounting hardware.
Details about the DLP projection system and supported resolutions.
Supported computer/video standards and aspect ratio options.
Information on displayable colors, zoom ratio, and projection lens.
Specifications for projection distance and horizontal/vertical scan rates.
Details on lamp, audio, dimensions, power supply, and consumption.
Operating temperature range and standard package contents list.
List of available input/output connectors including HDMI, RS232, Audio, and LAN.
Table of VGA analog PC signal modes, resolutions, and frequencies.
Table of HDMI PC signal modes, resolutions, and frequencies.
Table of HDMI extended wide timing modes and frequencies.
Tables for HDMI video signal and 1.4a 3D timing modes.
Table of MHL signal modes, resolutions, and frequencies.
FCC compliance information and measures to correct interference.
Requirements for cables, peripherals, and operational conditions.
Compliance notices and remarks for Canadian users.
Regulatory information for models with wireless LAN/Bluetooth and general compliance.
Declaration of conformity with EMC, R&TTE, and LVD Directives.
Declaration of conformity with RoHS and ErP Directives.
Information on frequency bands and maximum radio-frequency power.
FCC declaration of conformity, including manufacturer/importer details.
To Next Page
