How to fix ActronAir Controller set-temp that can’t be adjusted?
If you're unable to adjust the set temperature on your ActronAir Controller, and an EXX code is displayed on the wall controller, record the digits following 'E' and contact your installer. Also, ensure you are not exceeding the set-temperature limits on your wall control, and verify that the upper and lower temperature limits are correctly configured.
Why ActronAir Controller 7-day time clock is not accepting times I enter?
If the 7-day time clock on your ActronAir Controller isn't accepting the times you enter, make sure that the times do not overlap with those from another day. Also, ensure you are not trying to set the time past the maximum allowable limit.
Why is the ActronAir Controller cooling/heating not sufficient?
Insufficient cooling or heating in your ActronAir Controller can occur if the return air filter is clogged with dust and dirt. Ensure that the air inlet and outlet on the outdoor unit are not blocked. Also, the outside temperature being above or below the design conditions may affect the cooling/heating function.
What to do if ActronAir LM24-2W system does not start?
If your ActronAir Controller system doesn't start, verify that at least 5 minutes have passed since turning it on, as the system includes built-in safety timers. Also, check that your thermostat settings are correct and that the thermostat set-point is appropriately low for cooling or high for heating.
What to do if air does not flow from ActronAir Controller Indoor Unit?
If air isn't flowing from the indoor unit of your ActronAir Controller, ensure that the zones are switched on, if applicable. Note that during heating, air might not flow for about 15 seconds after startup to prevent cold drafts. Also, during defrosting of the outdoor unit in heating mode, the indoor fan may not operate for several minutes to prevent cold air from being blown into the rooms.
Why is my ActronAir Air Conditioner Accessories cooling/heating not sufficient?
Insufficient cooling or heating in your ActronAir Air Conditioner Accessories might occur if the return air filter is clogged with dust and dirt, hindering effective operation. Additionally, ensure that the air inlet and outlet on the outdoor unit are not obstructed. The outside temperature being above or below the design conditions can also affect performance.
What to do if ActronAir Air Conditioner Accessories system does not start?
If your ActronAir Air Conditioner Accessories system doesn't start, first, verify that at least five minutes have passed since turning it on, as the system incorporates built-in safety timers. Next, check that the thermostat settings are correct. Also, ensure the thermostat set-point is adequately low for cooling or sufficiently high for heating.
How to fix ActronAir Air Conditioner Accessories when set-temp can’t be adjusted?
If you're unable to adjust the set temperature on your ActronAir Air Conditioner Accessories, and an EXX code is displayed on the wall controller, record the digits following 'E' and contact your installer. Also, verify that you are not exceeding the set-temperature limits on your wall control. You should also check that the upper and lower temperature are set correctly.
What to do if air does not flow from ActronAir Air Conditioner Accessories indoor unit?
If air isn't flowing from the indoor unit of your ActronAir Air Conditioner Accessories, check that the zones are switched on, if applicable. During heating, air might not flow for about 15 seconds after startup to prevent cold drafts. Also, during the defrost cycle of the outdoor unit in heating mode, the indoor fan might not operate for several minutes to avoid blowing cold air into rooms.
Why is ActronAir Air Conditioner Accessories 7-day time clock not accepting times?
If the 7-day time clock on your ActronAir Air Conditioner Accessories isn't accepting the times you enter, ensure that you don't have overlapping times from another day. Also, verify that you're not attempting to set the time past the maximum allowable limit.
General| Model | LM24-2W |
|---|---|
| Display | LCD |
| Connectivity | Wired |
| Wireless | No |
| Backlight | Yes |
| Compatibility | ActronAir Ducted Systems |
| Control Modes | Cool, Heat, Fan, Auto |
| Temperature Range | 16°C - 30°C |
To Next Page
