Adax NEO User Manual

28
GB/AU
OFFICE MODE (OF)
StartupandReset – must be carried out after a long power cut or at
rst time use.
A Startup/Reset procedure has to be performed to initiate the correct
mode and function of the heater.
IMPORTANT: there are two different startup sequences
1) If °C-17-rE is ashing in the display: go to procedure A.
2) If HO is ashing in the display: go to procedure B.
The procedure must be completed in one continuous sequence to be
valid. Should the procedure be performed incorrectly or fail, switch off
the heater and start a new reset procedure.
StartupprocedureA–iftheheaterhasbeenconnectedand
switchedonbeforehand:
On switching heater on, the sequence
°C – 17 – rE - will ash in the display.
This means that the thermostat has
been disconnected for a long period
and needs to be restarted.
To set the heater back to the factory
default, switch off the heater using the
main power switch.
Press and hold in and at the same
time switch on using the main power
switch.
Continue to press until rE ashes in
the display, then release .
After a few seconds HO will ash in
the display.
You can choose between the modes HO
(Home), OF (Ofce) and CA (Cabin) by
pressing the or key.
Conrm your choice by holding in the
key for more than 5 seconds.
22 (°C) will ash. Select your preferred
comfort temperature.
Conrm by holding in the key for
more than 5 seconds.
If you do nothing, 22 (°C) will be
stored automatically after 7 seconds.
Starting the temperature cutback function
Three hours before you usually leave
the ofce press down on for 5
seconds (e.g. At 14:00 –
2 PM – press for 5 seconds).
h (hours) will ash for three seconds,
then 12 (hours) will ash. Select the
number of hours you want cutback to
be active by pressing or .
(NB! Cutback will start after three
hours.) Conrm by pressing briey.
d (day) will be displayed steadily for
three seconds. Then a random number
will ash (1 = Monday, 2 = Tuesday,
etc). Select the correct day using or
and conrm by pressing briey.
°C will ash three times and then 17
(°C) will ash continuously. With
the or key select your preferred
cutback temperature.
Conrm by pressing key briey.
Comfort temperature will continue for
three hours before the cutback starts
automatically.
(E.g. At 17:00 – 5 PM – the cutback
period will start and the LED (1) will
ash slowly.)
Cutback indicator
During the cutback period the LED (1)
will ash slowly. When it is lit stead-
ily, it indicates that cutback function is
not currently active but will start at the
appropriate time of the evening.
Working overtime
Press for 5 seconds. The set
comfort temperature will show in the
display. The LED above the key
will light steady while the LED above
the key will continue ashing. You
now have a temporary comfort period
lasting ve hours.
To cancel a period of temperature cutback
Hold down on and press once on
to override the currently active period
– or the next period of temperature
cutback. The lamp is lit steadily for
the period in question. Temperature
cutback periods will resume as usual
from the following period.
StartupprocedureB–iftheheaterhasneverbeenswitchedon
sinceleavingthefactory:
When the heater is switched on, HO
(Home mode) will ash in the display.
You can select between modes HO, OF
(Ofce) and CA (Cabin) by pressing the
or key.
Conrm your choice by pressing in
key for more than 5 seconds.
22 (°C) will ash. Select your preferred
comfort temperature.
Conrm by pressing in the key more
than 5 seconds.
If you do nothing, 22 (°C) will be
stored automatically after 7 seconds.

Adax NEO Specifications

General

Type	Electric heater
Power Output	2000W
Color Options	White, Black
Installation	Wall-mounted
Voltage	230V
Frequency	50Hz
Safety Features	Overheat protection
Features	Child lock