(44A4744/32XX)
VOLTAGE DRIVEN, 220-240V MONITORED
MONITORED WIRING SCHEMATIC
Information contained on this drawing is to be soley used
L-804 RGL VOLTAGE DRIVEN
97R0001
43A2389
A Siemens Company
ADB A Siemens Company
is strictly prohibited except as ADB-ALNACO may otherwise agree in writing.
for the purpose for which it was submitted. Any disclosure of this information
Copyright
1997
c
DRAWING NUMBER:
REVISION
BWH
DRAWN BY:
DESCRIPTIONLEVEL
ASSOCIATED DRAWINGS:
.
REV
NUMBER
ECO REV
25NOV98
DATE
BY
DRAWN DATE:
DRAWN
PROJECT NUMBER:
DRAWING TITLE:
PROJECT TITLE:
authorized copy.
APPRVD BY:
1 = 1
O
REV.
SHEET NUMBER:
SCALE:
2 OF 2
Tel: 614-861-1304
Fax: 614-864-2069
Columbus, Ohio 43230
977 Gahanna Parkway
DATE:
44A5864/1
(PROVIDED)
CONTROLLED COPY
part is prohibited. Initialed in RED ink below indicates
Unauthorized duplication of this document in whole or
WH
OR
GN
RD
OR
BK
GN
RD
WH
BK
175 VA
FOR 220-240 VAC INPUT
12
115/230 VAC
24 VAC
TO
6
WH
OR (COMM)
MONITOR
CONNECTIONS
GN (NC)
RD (NO)
(44A4744/22XX)
VOLTAGE DRIVEN, 120V MONITORED
OR (COMM)
175 VA
(PROVIDED)
44A5864/1
8
11
7
L1
5
2
1
T1
BK
WH
OR
RD
GN
FOR 120 VAC INPUT
BK
BK
OR
RD
GN
WH
MONITOR
CONNECTIONS
RD (NO)
GN (NC)
T1
L1
12 6
115/230 VAC
24 VAC
TO
WH
7
8
11
2
5
1
BK
L2
NC
PC
NO
J2
MON
AUX
AUX
LB1
LA2
LB2
T2
P5
T2
LB1
LA1
LB2
LA2
LA1
T1
T1
LAMP 1
LAMP 2
PC
L2
MON
NO
NC
T2
LB1
AUX
LB2
LA2
AUX
T1
LB2
LA1
LA2
LB1
LA1
J2
T1
LAMP 1
LAMP 2
P5
T2
SCREW TERMINALS - USE RING TERMINAL70A0027 ON
LAMP AND POWER CONNECTIONS.
NOTES: 1) WIRE LEADS CAN ALSO BE CONNECTED TO CORRESPONDING
NO JUMPER
NO JUMPER
94A0345/240 MOV ASSY.
44A6340 PCB-TO-LAMPHARNESS (2 PLC.S)
44A6339/120 RGL HARNESS, 120V
44A6339/240 RGL HARNESS, 240V
44A6340 PCB-TO-LAMPHARNESS (2 PLC.S)
OPTIONAL 220-240V MONITORING PROD./FIELD MOD. KIT (94A0390); SEE NOTE 2.
2) ATTEMPTING TO CONNECT 220-240V TO THE MONITORING CONTACTS CAN CAUSE MOV's
Z1-5 TO BLOW BECAUSE THE MONITORING CONTACTS ARE NOT RATED FOR THAT VOLTAGE.
TO AVOID THIS PROBLEM, ADD A WIRE (94A0390 KIT) FROM PIN #5 OF T1 TO THE "MON"
TERMINAL OF J2 ON THE 220-240V RGL PCB. NOTE:
THE WIRE GOING FROM L2 OF J2
TO PIN #2 OF T1 CAN ALSO BE USED FOR THIS PURPOSE IF THE PHOTOCELL ISN'T BEING
USED. AFTER DOING THIS, THE RGL WILL SUPPLY 110-120VAC BETWEEN THE GREEN AND
WHITE WIRES (NC AND NEUTRAL) WHEN THE RGL IS OPERATING NORMALLY WITH NO LAMPS
OUT. THIS VOLTAGE CAN BE USED TO DRIVE A RELAY WITH A110-120VAC COIL. ALSO
NOTE: WITH THIS ADDED WIRE, MOV's Z1-5 MAY BLOW IF THE POWER SWITCH TO THE RGL
SWITCHES NEUTRAL INSTEAD OF LINE.
N
01511
ADDED FUSE KIT OPTION
BE
20DEC05
94A0345 MOV ASSY.
120V=3A FUSES (47A0208)
120V IN-LINE
FUSE KIT OPTION
94A0453
240V=1.5A FUSES (47A0030)
94A0453/240
240V IN-LINE
FUSE KIT OPTION
O
02606
ADDED GND WIRES
BE
15APR10
EARTH
CONNECTION
16 GA, GRN/YEL
89A0163/6
(CONTRACTOR WIRED)
EXT. BOX
GND LUG
DOOR TETHER
CONNECTION
EARTH
CONNECTION
16 GA, GRN/YEL
89A0163/6
(CONTRACTOR WIRED)
EXT. BOX
GND LUG
DOOR TETHER
CONNECTION
PHOTOCELL
(OPTIONAL)
BK
RD
WH
GN
RD
OR
PHOTOCELL
(OPTIONAL)
RD
BK
WH
GN
OR
RD
BK
WH
BK
WH
TETHER CABLE BOLT
TETHER CABLE BOLT
To Next Page
Loading...
