ADC ADG-75D User Manual

ADC Part No. 113035
For replacement parts, contact the distributor from which the dryer
was purchased or
American Dryer Corporation
88 Currant Road
Fall River MA 02720-4781
Telephone: (508) 678-9000 / Fax: (508) 678-9447
E-mail: techsupport@amdry.com
020698JEV/tf
WARNING: For your safety the
information in this manual must be
followed to minimize the risk of fire or
explosion or to prevent property damage,
personal injury or death.
Do not store or use gasoline or other flammable
vapor and liquids in the vicinity of this or any
other appliance.
WHAT DO YOU DO IF YOU SMELL GAS
* Do not try to light any appliance.
* Do not touch any electrical switch; do not use
any phone in your building.
* Clear the room, building or area of all
occupants.
* Immediately call your gas supplier from a
neighbor's phone. Follow the gas supplier's
instructions.
* If you cannot reach your gas supplier, call the
fire department.
Installation and service must be performed by a
qualified installer, service agency or the gas
supplier.
AVERTISSEMENT: Assurez-vous de bien
suivre les instructions données dans cette
notice pour réduire au minimum le risque
dincendie ou dexplosion ou pour éviter tout
dommage matériel, toute blessure ou la mort.
Ne pas entreposer ni utiliser dessence ni
dautres vapeurs ou liquides inflammables dans
le voisinage de cet appareil ou de tout autre
appareil.
QUE FAIRE SI VOUS SENTEZ UNE ODEUR
DE GAZ:
* Ne pas tenter dallumer dappareil.
* Ne touchez à aucun interrupteur. Ne pas
vous servir des téléphones se trouvant dans
le bâtiment où vous vous trouvez..
* Évacuez la pièce, le bâtiment ou la zone.
* Appelez immédiatement votre fournisseur de
gaz depuis un voisin. Suivez les instructions
du fournisseur.
* Si vous ne pouvez rejoindre le fournisseur
de gaz, appelez le service des incendies.
Linstallation et lentretien doivent être assurés
par un installateur ou un service dentretien
qualifié ou par le fournisseur de gaz.
AD-75
Installation/Operator’s Manual
(DSI Gas/Electric/Steam)

ADC ADG-75D Specifications

General

Brand	ADC
Model	ADG-75D
Category	Dryer
Language	English

Summary

SECTION I IMPORTANT INFORMATION

RECEIVING and HANDLING

Procedures for inspecting and handling the dryer upon delivery to identify and report shipping damage.

SAFETY PRECAUTIONS

Crucial safety warnings and guidelines to prevent fire, explosion, injury, or death.

SECTION II SPECIFICATIONS/COMPONENT IDENTIFICATION

SPECIFICATIONS

Detailed technical specifications and dimensions for the dryer model.

COMPONENT IDENTIFICATION

Illustrates and labels the main components visible on the front and rear of the dryer.

SECTION III INSTALLATION PROCEDURES

LOCATION REQUIREMENTS

Guidelines for selecting an appropriate and safe installation location for the dryer.

EXHAUST REQUIREMENTS

Outlines the specifications and procedures for installing the dryer's exhaust ductwork system.

ELECTRICAL INFORMATION

Guidelines for proper electrical connections, grounding, and compliance with codes.

GAS INFORMATION

Information and requirements regarding the gas supply for the dryer, including codes and safety.

STEAM INFORMATION

Specifies steam requirements, installation, and maintenance guidelines for steam models.

SECTION I. PREPARATION FOR OPERATION/START-UP

PREOPERATIONAL TESTS

Procedures to test and verify proper operation of the dryer and its components before use.

PREOPERATIONAL INSTRUCTIONS

Step-by-step instructions for starting the dryer, both microprocessor and dual timer models.

SECTION VI ROUTINE MAINTENANCE

CLEANING

Guidelines for regular cleaning of the dryer and ductwork to maintain efficiency and prevent hazards.

ADJUSTMENTS

Procedures for inspecting and adjusting various components and safety devices after installation and periodically.

SECTION VII PROCEDURE FOR FUNCTIONAL CHECK OF REPLACEMENT COMPONENTS

Microprocessor (computer) Board

Steps to check the functionality of the microprocessor board after installation or replacement.

Direct Spark Ignition (DSI) System

Instructions for verifying the proper operation of the Direct Spark Ignition (DSI) system.

SECTION VIII REVERSING TIMER SPIN/DWELL ADJUSTMENTS

SECTION IX TECHNICAL INFORMATION

DATA LABEL

Explanation of the information contained on the dryer's data label for identification.

SECTION X TROUBLESHOOTING

MICROPROCESSOR (COMPUTER) MODELS

Troubleshooting steps for issues related to microprocessor-controlled dryer models.

TIMER MODELS

Troubleshooting steps for issues related to timer-controlled dryer models.