ADC ML-122 User Manual

ADC Part No. 113071
For replacement parts, contact the reseller from which the dryer
was purchased or
American Dryer Corporation
88 Currant Road
Fall River MA 02720-4781
Telephone: (508) 678-9000 / Fax: (508) 678-9447
E-mail: techsupport@amdry.com
www.amdry.com
051599GS/abe
WARNING: For your safety the
information in this manual must be
followed to minimize the risk of fire or
explosion or to prevent property damage,
personal injury or death.
Do not store or use gasoline or other flammable
vapor and liquids in the vicinity of this or any
other appliance.
WHAT DO YOU DO IF YOU SMELL GAS
* Do not try to light any appliance.
* Do not touch any electrical switch; do not use
any phone in your building.
* Clear the room, building or area of all
occupants.
* Immediately call your gas supplier from a
neighbor's phone. Follow the gas supplier's
instructions.
* If you cannot reach your gas supplier, call the
fire department.
Installation and service must be performed by a
qualified installer, service agency or the gas
supplier.
AVERTISSEMENT: Assurez-vous de bien
suivre les instructions données dans cette
notice pour réduire au minimum le risque
d’incendie ou d’explosion ou pour éviter tout
dommage matériel, toute blessure ou la mort.
Ne pas entreposer ni utiliser d’essence ni
d’autres vapeurs ou liquides inflammables dans
le voisinage de cet appareil ou de tout autre
appareil.
QUE FAIRE SI VOUS SENTEZ UNE ODEUR
DE GAZ:
* Ne pas tenter d’allumer d’appareil.
* Ne touchez à aucun interrupteur. Ne pas
vous servir des téléphones se trouvant dans
le bâtiment où vous vous trouvez.
* Évacuez la pièce, le bâtiment ou la zone.
* Appelez immédiatement votre fournisseur de
gaz depuis un voisin. Suivez les instructions
du fournisseur.
* Si vous ne pouvez rejoindre le fournisseur
de gaz, appelez le service des incendies.
L’installation et l’entretien doivent être assurés
par un installateur ou un service d’entretien
qualifié ou par le fournisseur de gaz.
ML-122
Installation Manual

ADC ML-122 Specifications

General

Brand	ADC
Model	ML-122
Category	Dryer
Language	English

Summary

Important Information (Section I)

Receiving and Handling Dryer

Procedures for inspecting and handling the dryer upon delivery.

Dryer Safety Precautions

Essential safety guidelines to prevent fire, explosion, or injury.

Specifications and Component Identification (Section II)

Gas and Steam Dryer Specifications

Detailed technical specifications for gas and steam dryer models.

Dryer Component Identification

Identification of various dryer components with diagrams.

Installation Procedures (Section III)

Location Requirements

Guidelines for selecting a suitable installation location for the dryer.

Unpacking and Setup Procedures

Steps for removing the dryer from packaging and preparing it for installation.

Dryer Enclosure and Clearance Requirements

Specifies clearances needed around the dryer for installation and service.

Fresh Air Supply Requirements

Details on providing adequate fresh air for dryer operation and combustion.

Exhaust Ductwork Requirements

Guidelines for proper exhaust ductwork design and installation.

Electrical Installation Information

Requirements for electrical connections, wiring, and service.

Gas Supply and Connection Information

Details on gas supply, connections, and safety for gas models.

Steam Supply and Connection Information

Requirements for steam supply, connections, and operation.

Compressed Air Requirements

Requirements for compressed air supply for pneumatic systems.

Operation and Start-Up Preparation

Checklist of items to verify before operating the dryer.

Pre-Operational Testing

Procedures for testing the dryer before initial use.

Service and Parts Information (Section IV)

Obtaining Dryer Service

Guidance on obtaining qualified service for the dryer.

Ordering Replacement Parts

Information on how to order replacement parts for the dryer.

Warranty Information (Section V)

Returning Warranty Cards

Instructions for completing and returning warranty cards.

Dryer Warranty Details

Information on obtaining a copy of the dryer's commercial warranty.

Warranty Parts Return Procedure

Procedures for returning parts for warranty claims.

Routine Maintenance (Section VI)

Dryer Cleaning Procedures

Recommended cleaning procedures and frequency for the dryer and its components.

Dryer Adjustments

Procedures for inspecting and adjusting dryer components.

Dryer Lubrication Information

Information on dryer lubrication requirements.

Reversing Timer Spin/Dwell Adjustments (Section VII)

Spin and Dwell Time Adjustment Guide

How to adjust spin and dwell times using mode selection switches.

Functional Check of Replacement Components (Section VIII)

Microprocessor Controller Board Functional Check

Steps to check the functionality of the replacement control board.

Hot Surface Ignition System Functional Check

Procedures for testing the HSI system after component replacement.