ADEMCO 4192SDM User Manual

~~
4192SDM/SDTM Addressable Photoelectronic Smoke Detector
Installation And Maintenance Instructions
Before installing detectors, please thoroughly read the suppoting Ademco control panel installation instructions, wtich
provide detailed information on detector spacing, placement, zones, and special applications. Copies of the installation
instructions are available from Ademco. NFPA 72 and NEMA guidehnes should also be observed.
.-
-
Use this smoke detector only with panels that support the detector’s mainttsnance feature
ADEMCO VISTA 150, First Alert FAI 600C.
GENERAL DESCRIPTION
The Model 4192SDM/SDTM photoelectronic smoke detector uses a state-of-the-ati optical sensing chamber. This detec-
tor is designed to provide open area protection and to be used with compatible UL-listed Ademco control panels.
An LED on each detector flashes every ten seconds. This LED can be latched on by code command from certain control
panels to indicate an alarm. It can also be unlatched to the normal blinking condition by the same control panels.
The 4192SDM/SDTM detector is intended for use in an Ademco 2-wire polling loop system. It uses two screw terminals
for connection to the system. Both detector power and communication between detector and control panel are accom-
plished over the same two wires.
SPECIFICATIONS
Base Dametec
Cover Height
Weight:
Loop Voltage Range:
Standby Current (max.):
Operating Temperature Range
4192SDM:
4192SDTM:
Loop Unit Load:
5.0 inches (127 mm)
3.0 inches (76 mm)’
Add 0.5 inches (13 mm) for thermlal units
0.7 lb. (310 gm)
7to14VDC
1.56 mA (LED off); 3.56 mA (LED on)
32° to 131 ‘F (0° to 55”C)
NOTE Do not instal! Model 4192SDM in locations where normal ambient tem-
perature exceeds 12VF (49°C).
32” to 120”F (O” to 49°C)
NOTE: Do not install Model 4192SDTM in locations where normal ambient
temperature exceeds 120°F (49”C).
2
Rgure 1. Flush mounting of detector on octagon box Figure 2. Detector mounting bracket
AD400-13-02 1
lfj6-722-0<
Ademco, 165 Eileen Way, Syosset, NY 11791

ADEMCO 4192SDM Specifications

General

Brand	ADEMCO
Model	4192SDM
Category	Security Sensors
Language	English

Summary

Smoke Detector Installation and Maintenance Overview

General Description

Overview of the 4192SDM/SDTM photoelectronic smoke detector's optical sensing chamber and 2-wire polling loop system.

Specifications

Key technical details including dimensions, weight, loop voltage, current, and operating temperature ranges for the detector.

Detector Mounting and Wiring

Mounting Instructions

Methods for mounting the 4192SDM detector to electrical boxes or directly to the ceiling using provided hardware.

Tamper Resistance

Instructions on enabling and using the detector's tamper-resistant feature to prevent unauthorized removal.

Wiring Installation Guidelines

Best practices for wiring connections to the control panel, including wire gauge and polarity recommendations.

Detector ID and Testing Procedures

Information on detector addressing and the initial steps for testing detector functionality.

Detector Testing Methods

Calibrated Test Card Method

Step-by-step guide for using a test card to verify the detector's alarm response.

Control Panel Sensitivity Test

Procedure for testing detector sensitivity via the control panel, if supported.

Aerosol Generator Testing

Method for testing detector alarm activation using an aerosol generator.

Direct Heat Testing (4192SDTM)

Specific instructions for testing the 4192SDTM model using a heat source.

Maintenance and Safety Warnings

Routine Maintenance

Instructions for cleaning the detector's screen, cover, and sensing chamber to ensure proper operation.

Smoke Detector Limitations

Discussion of inherent limitations and factors affecting smoke detector performance and fire detection.

One Year Limited Warranty

Details of the manufacturer's one-year limited warranty for the security equipment.