ADEMCO 6128 - User Manual

N6484V3 3/96
5827BD and 5827BDE
WIRELESS BI-DIRECTIONAL KEYPADS
Used with 5800TM Transmitter Module
INSTALLATION INSTRUCTIONS and OPERATING GUIDE
Unless otherwise indicated, all information in this manual is applicable to both the 5827BD and 5827BDE
GENERAL INFORMATION
The 5827BD and 5827BDE Wireless Bi-directional Keypads are
designed to be used in conjunction with a 5800TM Transmitter
Module. Additional 5827BDs (any quantity) may be used in
conjunction with the same 5800TM; however, no more than eight
5827BDEs may be used. The 5800TM is compatible with any
control panel that is
also equipped with a 4281 type (5700 System)
or 5881 type (5800 System) RF receiver.
Note: The 5827BDE is an enhanced version of the 5827BD and
employs AdemcoÕs new SignalSentryª technology, which
can provide high security wireless transmissions when used
in conjunction with the 5881EH RF receiver.
The 5827BD and 5827BDE can operate the protection system
similarly to other wireless keypads, via keypad buttons. In addition,
three LEDs (Red, Green, and Yellow) and a piezoelectric sounder
can indicate status information relative to:
System arming/trouble/emergency, RF transmission/confirmation,
and 5827BD/5827BDE programming and power.
The keypad configuration is similar to that of standard keypads. The
[
★
] key, however, is also the [ON/STAT] (power-up and system
status inquiry) key instead of a "READY" key, as it is on other
keypads (see
OPERATION ). There are three panic keys: A, B, and
C, comparable to the individual keys (or panic key pairs of [1] & [
★
],
[
★
] & [#], and [3] & [#] respectively) on other keypads.
The 5827BD and 5827BDE keypads, if so-programmed, also
feature "Quick Key" operation, which allows use of the [#] key
instead of entry of the security code when performing functions.
5800TM Transmitter Module
For every installation of one or more 5827BD or 5827BDE Wireless
Keypads, one 5800TM is required. The 5800TM complements the
RF receiver in that it transmits the information to be displayed on, or
sounded by, the 5827BD or 5827BDE. No modification to the
control is necessary. The 5800TM connects directly to the control's
wired keypad connection points, as described later.
ARM
OFF
AWAY
STAY
MAXIMUM
TEST
BYPASS
INSTANT
ON/STAT
CODE
CHIME
SEND/RCV READY
1
2
3
45
6
78
9
*
0
#
ANTENNA
(OPTIONAL)
SOUNDER
PANIC KEYS
POWER-UP KEY
5827BD
AFFIX
PANIC KEY
LABELS HERE
LEDS
GREEN
YELLOW
RED
C (3/#)
B (★/#)
A (1/★)
5827BD & 5827BDE INSTALLATION
The 5827BD and 5827BDE are designed to be portable, for use
throughout the protected premises. If desired, a wireless keypad
may be stored on its accompanying mounting bracket (easily
installable via two countersunk mounting holes). Keyhole slots on
the rear of the keypad slip onto two hooks on the mounting bracket,
allowing the keypad to be easily removed when desired .
When operating, or selecting a location for storing the wireless
keypad, observe the same precautions as used for locating the
wireless system's other transmitters (see the control panel's
instruction manual). For example, operating the keypad on or near
large metal objects may decrease range and/or block
transmissions.
1. Install the keypad's 9-volt Alkaline battery. Slide off the
battery compartment cover at the rear of the keypad and insert
the battery. Observe polarity! Then replace the cover.
2. Program the keypad's memory as indicated next.
Programming the Wireless Keypad
a. Power up the keypad by depressing the [
★
] key. The
yellow LED will blink.
If the keypad was previously programmed, the system
status may also be annunciated (see
Power-up and
System Status Inquiry
on the next page).
b. Enter the keypad programming mode by
depressing both the [1] and [3] keys at the same time
for 3 seconds.
Alternate blinking of the red and green LEDs confirms
that the unit is in the keypad programming mode.
c. Program the desired functions, in the order given
in the Programming table that follows. Note that
every sequence starts with a [
★
] and ends with a [#].
Previous Menu
For use with Q.E.D. control panels only.

Summary

General Information

5800 TM Transmitter Module

Describes the function and requirement of the 5800TM Transmitter Module for wireless keypad operation.

5827 BD & 5827 BDE Installation

Details the initial steps for installing the wireless keypad, including battery insertion and programming.

Programming Table for 5827 BD and 5827 BDE

5800 TM Transmitter Module Installation

Provides instructions for installing the 5800TM Transmitter Module, including wiring connections.

5800 TM Transmitter Module Programming

Explains how to program the 5800TM Transmitter Module for addressable and non-addressable systems.

Operation

Details the operational aspects of the wireless keypad.

Power-up and System Status Inquiry

Details how to power up the keypad and inquire about system status using the [ON/STAT] key.

System Status Indications for 5827 BD;5827 BDE

Routine Operation

Explains the routine operation of the keypad for arming, disarming, and chime functions.

Quick Key Operation

Details the Quick Key feature, allowing functions via the [#] key instead of a security code.

Panic Keys

Describes the function and operation of the panic keys (A, B, C) on the wireless keypad.

Alarm Memory

Enrolling a 5827 BDE as a SignalSentry Device

Procedure for enrolling the 5827BDE for high-security SignalSentry wireless transmissions with the 5881EH receiver.

Returning a 5827 BDE To Its Normal Operating Mode (Non-SignalSentry)

Steps to revert an enrolled 5827BDE from SignalSentry mode back to normal operation.

Returning All 5827 BDEs in the System To Their Normal (Non-SignalSentry) Mode

Enrollment Reset (All 5827 BDE Keypads Returned To Normal Operation)

Procedure to reset all enrolled 5827BDEs in the system to normal mode and delete serial numbers from the 5881EH.

5827 BD;5827 BDE Specifications

Ademco Limited Warranty

Details the limited warranty provided by Ademco for their alarm devices.

ADEMCO 6128 Specifications

Power

battery type	9-volt Alkaline
compatible batteries	Ademco 464, Duracell MN1604, Eveready 522

Indicators and Alerts

LED colors	Red, Green, Yellow
sounder frequency	4200 Hz
sounder functions	confirmation, trouble and emergency beeps, sounding on alarm

Weight and Dimensions

width	2-3/8"
height	6-1/4"
depth	1-1/4"