ADEMCO 6148ICON - User Manual

K5320-2V2 4/04 Rev. A

$'(0&2,&21
5(027(.(<3$'
INSTALLATION AND SETUP GUIDE
GENERAL INFORMATION
The 6148ICON is an addressable remote keypad designed
for use with ADEMCO control panels. Addresses are set via
the keypad keys. The keypad keys are continuously backlit
for convenience.
KEYPAD DISPLAY AND LEDS
The 6148ICON keypad contains icons and a three digit zone
identifier to display system status (the universal icons are
shown on page 3).
The following table describes the LEDs and their functions:
LED Function
(Red)
ARMED
Lights when the system is armed in any
mode.
(Green)
READY
Lights when the system is ready to be
armed.
RETAINING
SNAPS
NOTE:
TO REMOVE CASE BACK
PUSH IN THE TWO MOUNTING
SNAPS LOCATED ALONG THE
BOTTOM OF THE KEYPAD
AND LIFT UP.
6148-ICON-005-V0
✔
Figure 1. Removing the Case-back
USE AN
ADDITIONAL
MOUNTING
SCREW
HERE IF
CASE BACK
TAMPER IS
TO BE USED
ENTRY HOLE
FOR HIDDEN
WIRING
KNOCKOUT FOR
SURFACE WIRING
KNOCKOUT FOR
SURFACE WIRING
6148-ICON-008-V0
MOUNTING
HOLES
KNOCKOUT
FOR
SURFACE
WIRING
RETAINERCLIP
Figure 2. Mounting and Wiring Entry
6148-ICON-009-V0
CASE
BACK
CLIP
KEYPAD
DRILL
BIT
✔
Figure 3. Locking Clip Installation (if required)
SPECIAL-FUNCTION KEY PAIRS
The keypad also features special-function key pairs. These
key pairs may be used to activate panic alarms. See the
control's instructions for more details.
The following key pairs are used by the 6148ICON to
manually activate silent emergency, audible emergency,
personal emergency, or fire alarms:
x
[1] & [✱]
x
[✱] & [#]
x
[
3
] & [#]
Key pairs activate immediately.
CASE TAMPER
A built-in tamper switch detects separation of the case-back
from its mounting surface. To include tamper protection, an
additional mounting screw must be inserted in the case-
back, as shown in Figure 2.
The 6148ICON supports keypad tamper reporting. If the
control panel supports the tamper feature, no additional
keypad programming is required. A tamper violation is
reported on the keypad by displaying the keypad address in
trouble, preceded by the digit 1. For example, if there are
three keypads connected with addresses of 16, 17, and 18
respectively, and a tamper violation occurs with keypad
address 17, the other keypads would display
that
keypad’s
violation as 117.

Summary

GENERAL INFORMATION

Keypad Display and LEDs

Describes the keypad's three-digit zone identifier and LED functions for system status.

Special-Function Key Pairs

Details key combinations used to activate panic alarms like silent, audible, or fire alarms.

Case Tamper Protection

Explains the built-in tamper switch and how tamper violations are reported.

WIRING AND INSTALLATION

Keypad Mounting and Wiring

Covers surface mounting, routing wires through knockouts, and connecting to the terminal block.

Setting the Keypad Address

Guides on how to enter address mode and set the keypad's address (00-30) or nonaddressable mode (31).

Viewing the Keypad Address

Instructions to display the current keypad address by pressing specific keys.

UNIVERSAL ICONS

Keypad Display Icons Overview

Illustrates universal icons for quick interpretation of security system status and conditions.

Master List of Icons by Language

Provides a cross-reference of icon meanings in English and other languages for system status.

SPECIFICATIONS

ADEMCO 6148ICON Specifications

General

Brand	ADEMCO
Model	6148ICON
Category	Keypad
Language	English