ADT Safewatch Pro 3000 Programming Guide

–
3
–
352*5$00,1*)250
Entry of a number other than one specified will give unpredictable results. Values shown in brackets are factory defaults.
Field Function Data Entries Programmable Values
SYSTEM SETUP (
✱
20–
✱
29)
∗
20
INSTALLER CODE
| | | [6321]
4 digits, 0–9
✱
21
QUICK ARM ENABLE
[1,1]
Part. 1 Part.2
0 = no; 1 = yes
✱
22
RF JAM OPTION
[0]
0 = no RF Jam detection; 1 = send RF Jam report
UL: must be 1 if wireless devices are used
✱
23
FORCED BYPASS
[1,1]
Part. 1 Part. 2
0 = none UL: must be “0”
1 = bypass open zones
∗
24
RF HOUSE ID CODE
| | |
Part. 1 Part. 2 Common
00 = disable all wireless touchpad usage
01–31 = using 5827, 5827BD or 5804BD touchpad
[00,00,00]
✱
26
CHIME BY ZONE
[0]
0 = no; 1 = yes (select zones to chime on zone list 3,
using *81 Menu mode)
✱
27
X–10 HOUSE CODE
[0]
0 = A; 1 = B, 2 = C, 3 = D, 4 = E, 5 = F, 6 = G,
7 = H, 8 = I, 9 = J, #10 = K, #11 = L, #12 = M, #13 = N,
#14 = O, #15 = P UL: not for fire or UL installations
✱
28
ACCESS CODE FOR
4285/4286 PHONE MODULE
| [00]
(Partition 1 only)
00 = disable; 1st digit: enter 1–9; 2nd digit: enter # + 11
for "
✱
", or # + 12 for "#".
UL: must be “00” for UL Commercial Burg. installations
✱
29
LONG RANGE RADIO OUTPUT
[0]
0 = disable; 1 = enable
ZONE SOUNDS AND TIMING (
✱
31 –
✱
39)
✱
31
ONE AUDIBLE ALARM PER ZONE
[0]
0 = no UL: must be “0”
; 1 = yes
✱
32
FIRE ALARM SOUNDER TIMEOUT
[0]
0 = sounder stops at timeout;
1 = no sounder timeout UL: must be “1” for fire install.
✱
33
ALARM SOUNDER TIMEOUT
[1]
0 = none; 1 = 4 min; 2 = 8 min; 3 =12 min;
4 = 16 min; UL: minimum “1” (4 min.)
✱
34
EXIT DELAY
| | [60,60]
Part. 1 Part. 2
00–99 = seconds of exit delay time for each partition
Common zones use same delay as partition 1.
✱
35
ENTRY DELAY #1 (zone type 01)
| | [45,45]
Part. 1 Part. 2
00–99 = seconds of entry delay #1 time for each
partition; UL: 45 seconds max.
Common zones use same delay as partition 1.
✱
36
ENTRY DELAY #2 (zone type 02)
| | [90,90]
Part. 1 Part. 2
00–99 = entry delay #2 time for each partition;
UL: 60 seconds max.
Common zones use same delay as partition 1.
∗37
AUDIBLE EXIT WARNING
[1,1]
Part. 1 Part. 2
0 = no; 1 = yes
✱
38
CONFIRMATION OF ARMING DING
[0,0]
Part. 1 Part. 2
0 = no; 1 = yes (wired touchpads and RF)
2 = yes, RF only
✱
39
POWER UP IN PREVIOUS STATE
[1]
0 = no; 1 = yes UL: must be “1”
DIALER PROGRAMMING (
✱
40 –
✱
42)
Enter the number of digits shown. Do not fill unused spaces. Enter 0–9; #+11 for '
✱
'; #+12 for '#'; #+13 for a 2-second pause.
∗40
PABX ACCESS CODE
| | | | |
Enter up to 6 digits. If fewer than 6 digits are entered, exit by pressing [
✶
] and next
desired field number. To clear entries from field, press
✱
40
✱
.
∗41
PRIMARY PHONE No.
| | | | | | | | | | | | | | | | | | |
Enter up to 20 digits; Do not fill unused spaces. If fewer than 20 digits entered, exit by pressing [
✶
] and
next desired field number. To clear entries, press
✱
41
✱
.
∗42
SECOND PHONE No.
| | | | | | | | | | | | | | | | | | |
Enter up to 20 digits; Do not fill unused spaces. If fewer than 20 digits entered, exit by pressing [
✶
] and next
desired field number. To clear entries, press
✱
42
✱
.

ADT Safewatch Pro 3000 Specifications

General

Keypads	Supports multiple keypads
Communication	Landline, cellular
Remote Access	Via ADT Pulse (if subscribed)
Type	Wired
Power Supply	battery backup
Compatibility	ADT Monitoring Services
Sensors	Door/Window, Motion
Installation	Professional
Backup Battery	Yes