ADT Safewatch Pro 3000 Programming Guide

–
4
–
For fields *43 and *45:
Enter 0–9; #+11 for B; #+12 for C; #+13 for D; #+14 for E; [#+15 for F]. To clear entries from field, press
*
43
* or *
45
*
.
Examples: For Acct.
1234
, enter: 1 | 2 | 3 | 4 ; For Acct.
B234
, enter: #+11| 2 | 3 | 4
✱
43
SUBSCRIBER ID # (Part.1)
| | | / | | | | |
Enter 4 or 10 digits, depending on selection in *48
Report Format. See box above for entries.
✱
45
SUBSCRIBER ID # (Part. 2)
| | | / | | | | |
Enter 4 or 10 digits, depending on selection in *48
Report Format. See box above for entries.
✱
47
PHONE SYSTEM SELECT
[3]
If Cent. Sta.
IS NOT
on a WATS line:
0=Pulse Dial; 1=Tone Dial;
if Cent. Sta.
IS
on a WATS line:
2 = Pulse Dial ; 3 = Tone Dial
✱
48
REPORT FORMAT
[77]
primary secondary
5 = CID using 10-digit subscriber account (ID) no.
7 = CID using 4-digit subscriber account (ID) no.
14 = CID 4-digit account no. with shutdown (# + 14)
15 = CID 10-digit account no. with shutdown (# + 15)
UL: only 4-digit Contact ID format has been evaluated
✱
49
SPLIT/DUAL REPORTING
[0]
0 = Disable (Backup report only)
Primary Phone No. Second Phone No.
1 = Alarms, Restore, Cancel Others
2 = All except Open/Close, Test Open/Close, Test
3 = Alarms, Restore, Cancel All
4 = All except Open/Close, Test All
5 = All All
✱
50
15 SEC DIALER DELAY (BURG)
[1]
0 = no UL: must be “0”
; 1 = yes
✱
53
MISC. FAULT DELAY TIME
(Zone Type 25 or Configurable Zone Type)
[0]
0 = 15 seconds 6 = 2-1/2 min #+12 = 8 min
1 = 30 seconds 7 = 3 min #+13 = 10 min
2 = 45 seconds 8 = 4 min #+14 = 12 min
3 = 60 seconds 9 = 5 min #+15 = 15 min
4 = 90 seconds #+10 = 6 min
5 = 2 minutes #+11 = 7 min
UL: may only be used on non-burglar alarm/ non-fire alarm
zones when used in fire and/or UL burglar alarm installation
✱
54
DYNAMIC SIGNALING DELAY
[0]
Delay selectable from 0 to 225 secs in 15-sec
increments.
0 = no delay (both signals sent), 1 = 15 secs,
2 = 30 secs, etc. UL: must be “0”
✱
55
DYNAMIC SIGNALING PRIORITY
[0]
0 = Primary Dialer first; 1 = Long Range Radio first.
TO PROGRAM SYSTEM STATUS, & RESTORE REPORT CODES (
✱
59 –
✱
76, &
✱
89) FOR CONTACT ID® REPORTING:
Enter any digit (other than "0") in the
first
box, to enable zone to report (entries in the
second
boxes will be ignored).
UL: see installation instructions for requirements
SYSTEM STATUS REPORT CODES (
✱
59–
✱
68)
✱
59
EXIT ERROR REPORT CODE
[1] Any non-zero entry enables CID report.
✱
60
TROUBLE REPORT CODE
| [10] Any non-zero entry in first digit enables CID report.
✱
61
BYPASS REPORT CODE
| [00] Any non-zero entry in first digit enables CID report.
✱
62
AC LOSS REPORT CODE
| [00] Any non-zero entry in first digit enables CID report.
✱
63
LOW BAT REPORT CODE
| [10] Any non-zero entry in first digit enables CID report.
✱
64
TEST REPORT CODE
| [10] Any non-zero entry in first digit enables CID report.
Use Scheduling mode to schedule periodic test reports.
✱
65
OPEN REPORT CODE
[0,0,0] Any non-zero entry enables CID report for partition.
Part. 1 Part. 2 Common
✱
66
ARM AWAY/STAY RPT CODE
[0,0,0,0,0,0] A
ny non-zero entry enables
Away Stay Away Stay Away Stay CID report
Part. 1 Part. 2 Common
✱
67
RF XMTR LOW BAT REPORT CODE
| [10] Any non-zero entry in first digit enables CID report.
UL: must be enabled if wireless devices are used
✱
68
CANCEL REPORT CODE
| [10] Any non-zero entry in first digit enables CID report.
Entry of a number other than one specified will give unpredictable results.

ADT Safewatch Pro 3000 Specifications

General

Keypads	Supports multiple keypads
Communication	Landline, cellular
Remote Access	Via ADT Pulse (if subscribed)
Type	Wired
Power Supply	battery backup
Compatibility	ADT Monitoring Services
Sensors	Door/Window, Motion
Installation	Professional
Backup Battery	Yes