AEG DDLE Basis 11 User Manual (English)

Other manuals for AEG DDLE Basis 11

Operating And Installation Instructions17 pages

Questions and Answers:

A
Angel KramerAug 13, 2025
How to fix AEG Water Heater when it doesn't start despite the tap being fully open?
- M
  Mario DavisAug 13, 2025
  If the heating system in your AEG water heater doesn't start even when the tap is fully open, here's what you can check: * **No voltage:** Inspect the fuses in your fuse board. * **Start-up volume not reached:** Clean and descale perlators in water taps or shower heads, as contamination or scaling may be the cause. * **Faulty heating system:** Call a service technician to test the heater and replace it if necessary.
K
Kiara BaileyAug 17, 2025
How to increase the flow rate of my AEG DDLE Basis 11 Water Heater?
- J
  jamescarrilloAug 17, 2025
  If the flow rate of your AEG water heater is too low, it might be caused by scaled up shower head/perlators or contamination. Descale and replace them if required. Also, clean the sieve.
V
Victoria HernandezAug 20, 2025
What to do if my AEG DDLE Basis 11 Water Heater has no hot water and no “traffic light” display?
- C
  Connor SmithAug 21, 2025
  If your AEG water heater isn't producing hot water and the traffic light display is off, here are a couple of things to check: * **Fuse/MCB:** Verify the fuse/MCB in your fuse box and replace if necessary. * **Safety pressure limiter:** If the safety pressure limiter has tripped, remove the cause of the fault. Open the downstream tap for 1 minute to depressurize and cool down the heating system. Then, press the pushbutton on the safety pressure limiter. If the issue persists, test the electronics PCB and replace if required.
R
Robert BaxterAug 25, 2025
Why my AEG DDLE Basis 11 Water Heater set temperature is not achieved?
- J
  Jamie CarterAug 25, 2025
  If your AEG water heater isn't reaching the set temperature, it could be due to one phase being down. Check the fuse/MCB in the fuse box.
K
knoxjustinAug 27, 2025
What does it mean if my AEG Water Heater has no hot water, throughput is > 3 l/min, and the traffic light displays constant yellow with green flashing?
- J
  jessezunigaAug 27, 2025
  If your AEG water heater shows these symptoms, consider the following possible causes: * The high limit safety cut-out may be triggered, so check and activate it if needed. * There could be a cable break. * The heating system might be faulty, so test the heating system resistor and replace if necessary. * Faulty electronics could also be the cause, so test the electronics PCB and replace if required.
L
laurenmurraySep 1, 2025
What to do if my AEG Water Heater has no hot water, throughput > 3 l/min, and the traffic light displays green flashing or constantly ON?
- A
  andersonkimSep 1, 2025
  If your AEG water heater exhibits these symptoms, it could be due to: * Faulty electronics, so test the electronics PCB and replace if necessary. * The flow sensor DFE might not be plugged in, so refit the plug of the electronics PCB. * The flow sensor DFE could be faulty, so check and replace the flow switch if required.
T
Tony ScottSep 4, 2025
Why does my AEG DDLE Basis 11 Water Heater not switch on and there is no hot water?
- T
  Timothy CoffeySep 4, 2025
  The air sensor may be detecting air in the water, causing the AEG water heater to switch off briefly. The device should restart after one minute.
J
Jonathan RichardsSep 8, 2025
Why does my AEG DDLE Basis 11 show constant red illumination and green flashing with no hot water?
- B
  Brooke JonesSep 8, 2025
  If your AEG water heater displays these symptoms, check the following: * The cold water inlet temperature might be above 35 °C. Reduce the temperature of the cold water supply. * The flow rate might be greater than 25 l/min. Reduce the device throughput. * The cold water sensor could be faulty. Test the electronics PCB and replace if required.