Why is the gearbox noisy on my AGRI EASE Lawn Mower?
A noisy gearbox in your AGRI EASE Lawn Mower can be due to worn bearings or low oil. Replace the bearing if it is worn. Check the oil level and add oil if it is low.
What causes belt rollover on my AGRI EASE Lawn Mower?
Belt rollover on your AGRI EASE Lawn Mower can occur due to a damaged belt, a foreign object in the sheave groove, or a worn sheave groove. Replace a damaged belt with the correct specified belt. Inspect all sheave grooves for rust, paint, or other foreign material and remove them if present. Replace a worn sheave groove with the correct specified sheave.
Why is the gearbox leaking on my AGRI EASE Lawn Mower?
A leaking gearbox on your AGRI EASE Lawn Mower can be caused by several issues, including a damaged oil seal, bent shaft, rough shaft in the oil seal area, incorrectly installed oil seal, or an oil seal not sealing in the housing. Replace the seal, or the seal and shaft if bent. If the shaft is rough, replace or repair it. Also, you can drain oil to the proper level, replace the gearbox, replace the gasket, or tighten bolts.
General| Brand | AGRI EASE |
|---|---|
| Model | BE-FM60RDG |
| Category | Lawn Mower |
| Language | English |
Detailed steps for applying safety signs correctly to equipment.
Key safety principles and precautions for operating equipment.
Guidelines for safely starting, stopping, and handling emergencies.
Procedures for safely storing the mower when not in use.
Details on dangers associated with the rotating driveline and safety measures.
Information on blade hazards and necessary precautions for safe operation.
Warnings and precautions regarding objects thrown by the mower blades.
General warnings and advice for safe operation and maintenance.
Details about hazards from moving parts and required safety actions.
Critical checks to perform before operating the mower.
Instructions for attaching rear brace bars and A-frame bars to the mower deck.
Connecting braces at the top of the A-frame with specified hardware.
Installing wheel support braces using M12 bolts and locking nuts.
Attaching the rear discharge chute and safety chains.
Adjusting mower deck height using spacers on the wheel assembly.
Guidelines for preparing the tractor to safely operate the mower.
Procedures for safely attaching the driveline yoke to the tractor PTO shaft.
How to adjust the mower's cutting height for optimal performance.
Specific tractor requirements and preparation steps for using the mower.
Safe procedures for starting, stopping, and emergency handling of the mower.
Guidelines on appropriate ground and PTO speeds for mowing.
Advice for achieving a clean cut and handling various grass conditions.
Steps for safely detaching and storing the mower after use.
Safety checks and considerations before transporting the mower.
Locations and recommended frequencies for lubricating mower components.
Instructions for filling and checking the gearbox oil level.
How to properly lubricate the driveline U-joints and telescoping tubes.
Procedure for lubricating blade spindle fittings.
Guidelines for using, servicing, and installing mower blades.
Proper method for sharpening mower blades for balance and edge.
Steps for adjusting the tension of the mower's drive belts.
Recommended steps for preparing the mower for long-term storage.
Causes and remedies for streaking patterns in cut grass.
Addressing issues with uneven grass discharge or bunching.
Identifying causes of belt damage and recommended repairs.
Causes and solutions for excessive vibration during operation.
Identifying reasons for belt slippage and how to fix them.
Causes and remedies for belt rollover issues.
Causes and remedies for mower belt breakage.
Addressing problems with blades scraping the ground.
Causes and solutions for gearbox overheating.
Identifying causes and fixes for gearbox oil leaks.
Causes and solutions for a noisy gearbox.
Reasons for premature blade wear and how to correct them.
Diagnosing why the mower requires excessive tractor power.
Addressing mower instability and side-to-side movement during cutting.
To Next Page
