AIMS Power PICOGLF10W12V120V

Questions and Answers

A
Ashley LynchAug 13, 2025
How to troubleshoot AIMS Power Inverter that will not turn on?
- D
  Donald LivingstonAug 13, 2025
  If your AIMS Power Inverter isn't turning on, the issue might stem from several causes: * The batteries may not be properly connected, or the connections on the battery side might be loose. * The battery voltage could be too low. To resolve this, verify that the batteries are correctly connected and that all cable connections are secure. Inspect the DC fuse and breaker. If the battery voltage is low, try charging the battery.
K
krystal61Aug 17, 2025
What to do if AC output voltage is low on AIMS Power PICOGLF10W12V120V Inverter?
- J
  Joyce BrownAug 17, 2025
  If the AC output voltage of your AIMS Power Inverter is low and it's turning off loads quickly, it's likely due to a low battery. Check the condition of your batteries and recharge them if needed.
T
Tyler LewisAug 20, 2025
Why is there no AC output voltage and no indicator lights on my AIMS Power PICOGLF10W12V120V Inverter?
- B
  Brenda BrooksAug 20, 2025
  If your AIMS Power Inverter shows no AC output voltage and no indicator lights are on, it's possible that the inverter has been manually switched to the OFF mode. To fix this, simply press the switch to either the 'Power saver on' or 'Power saver off' position.
R
Robert HartAug 25, 2025
Why is AIMS Power PICOGLF10W12V120V Inverter charger supplying a lower charge rate?
- N
  Nancy MitchellAug 25, 2025
  A lower charge rate from your AIMS Power Inverter's charger can be due to several reasons: * Improperly set charger controls. * Low AC input voltage. * Loose battery or AC input connections. To address this, check all DC/AC connections and ensure they are secure. Also, make sure you are using qualified AC power.
E
Eric BaldwinAug 28, 2025
Why do sensitive loads turn off temporarily when transferring between grid and inverting on AIMS Power Inverter?
- W
  William HarveyAug 28, 2025
  If sensitive loads are turning off temporarily during the transfer between grid and inverting, the inverter's low voltage trip voltage might be set too low for those specific loads. To solve this, choose narrow AC voltage in the DIP switch. If that doesn't work, consider installing a UPS (Uninterruptible Power Supply).
A
Alyssa SimmonsAug 31, 2025
What to do if AIMS Power PICOGLF10W12V120V Inverter charger turns off when charging from a generator?
- L
  lewisdestinySep 1, 2025
  If the charger turns off while charging from a generator, it could be due to high AC input voltages from the generator. Try loading the generator down with a heavy load or turning the generator output voltage down.
J
James KimSep 4, 2025
What to do if AIMS Power Inverter charger is inoperative and won't accept AC?
- T
  Timothy KnoxSep 5, 2025
  If the charger is inoperative and the unit won't accept AC, the AC voltage may have dropped out of tolerance. Check the AC voltage to ensure it's within the proper voltage and frequency range.
A
Ashley FischerSep 8, 2025
Why is my AIMS Power Inverter transformer/case making noise?
- N
  Nicole WalkerSep 8, 2025
  If you're hearing noise from the transformer or case of your AIMS Power Inverter, it could be due to specific loads being applied, such as a hair dryer. Try removing those loads to see if the noise stops.

AIMS Power PICOGLF10W12V120V Specifications

General

Input Voltage	12V DC
Output Voltage	120V AC
Efficiency	90%
Frequency	60 Hz
Cooling	Fan Cooled
Power Output	1000W
Surge Rating	2000W
Waveform	Pure Sine Wave
Protections	Overload, Over Temperature, Short Circuit