Why is my Airwell GC 9 DCI not cooling or heating even though all components are working?
If your Airwell Air Conditioner components appear to be working, but there is no cooling or heating, it's possible there is a refrigerant leak. You should check the refrigeration system.
What to do if my Airwell Air Conditioner is not responding to the remote control?
If your Airwell Air Conditioner isn't responding to the remote, the remote control message may not be reaching the indoor unit. First, check the remote's batteries. If the batteries are good, check the display and display wiring. If that's OK, replace the display PCB. If it's still not working, replace the controller.
What to do if my Airwell GC 9 DCI Air Conditioner is leaking water from the indoor unit?
If your Airwell Air Conditioner's indoor unit is leaking water, the drainage tube is likely blocked. Inspect the drainage tube and clear any blockages.
How to fix Airwell GC 9 DCI when the power supply indicator (Red LED) does not light up?
If the red LED power supply indicator on your Airwell Air Conditioner isn't lit, the unit may not be getting power. First, check the power supply. If the power supply is working, inspect the display and its wiring. If both are functioning correctly, the controller may need to be replaced.
How to troubleshoot an Airwell GC 9 DCI Air Conditioner when the indoor fan doesn't start?
If the louvers are open and the green LED is lit, but the indoor fan on your Airwell Air Conditioner isn't starting, it could be due to a couple of reasons. If the unit is in heat mode, the coil may not be warm yet, try changing to cool mode to check. Alternatively, there might be a problem with the PCB or capacitor. Change to high speed and verify the power supply to the motor is higher than 130VAC (for triack controlled motor) or higher than 220VAC for fixed speed motors, if OK replace capacitor, if not OK replace controller.
What should I do if my Airwell GC 9 DCI responds to the remote but the green LED doesn't light up?
If your Airwell Air Conditioner responds to the remote control but the green LED operate indicator doesn't light up, there may be a problem with the display PCB. Try replacing the display PCB. If the issue persists, replace the controller.
Why does my Airwell GC 9 DCI Air Conditioner compressor not start?
If the compressor on your Airwell Air Conditioner isn't starting, it could be due to an electronics control problem or a protection being triggered. Perform diagnostics (See 13.1.3 below), and follow the actions described.
What to do if Airwell Air Conditioner compressor stops during operation but the Green LED remains on?
If your Airwell Air Conditioner's compressor stops during operation while the green LED remains on, it may be an electronic control or power supply problem. Perform diagnostics (See 13.1.3 below), and follow the actions described.
Why is my Airwell Air Conditioner working in the wrong mode?
If your Airwell Air Conditioner is working in the wrong mode (cooling instead of heating, or vice versa), it could be due to electronics or a power connection issue to the RV. Check the RV power connections. If they are OK, check the RV operation with a direct 230VAC power supply. If it's still not working, replace the outdoor controller.
What causes the outdoor fan to not work when the compressor is on in my Airwell GC 9 DCI Air Conditioner?
If the compressor is running but the outdoor fan isn't working on your Airwell Air Conditioner, there may be a problem with the outdoor electronics or the outdoor fan itself. Check the outdoor fan motor according to the procedure in section 13.2.3 below. If it is not OK, replace the controller.
General| Type | Split System |
|---|---|
| Cooling Capacity | 9000 BTU/h |
| Energy Efficiency Ratio (EER) | 3.21 |
| Power Supply | 220-240V, 50Hz |
| Refrigerant | R410A |
| Power Consumption (Cooling) | 800W |
| Operating Temperature (Cooling) | 18°C to 43°C |
| Operating Temperature (Heating) | -7°C to 24°C |
To Next Page
