Why Airwell PNX009 Air Conditioner indoor unit doesn't respond to the remote control?
If the Airwell Air Conditioner indoor unit isn't responding to the remote control, it could be that the remote control message isn't reaching the unit. First, check the remote control batteries. If they are OK, check the display and display wiring. If that's OK, replace the display PCB. If the issue persists, replace the controller.
What to do if Airwell Air Conditioner compressor operates but generates no capacity?
If the compressor of your Airwell Air Conditioner is running but one or more units aren't generating capacity, it could be due to several reasons: * EEV problem: Check EEV. * Refrigerant leakage: Check the refrigeration system. * Indoor coil block: Clean filters and/or remove the block. * Outdoor coil block: Remove the block and/or avoid air by-pass.
Why is my Airwell PNX009 blowing air, but there is no cooling or heating?
If all components of your Airwell Air Conditioner are running but there's no cooling or heating, the cause might be a refrigerant leak. Check the refrigeration system.
What to do if Airwell PNX009 indoor unit is leaking water?
If your Airwell Air Conditioner's indoor unit is leaking water, the drainage tube might be blocked. Inspect the drainage tube and clear any blockages.
How to fix Airwell PNX009 when the indoor unit power indicator is off?
If the red LED indicating power supply on your Airwell Air Conditioner indoor unit is not lit, there may be no power supply. Check the power supply first. If the power supply is OK, check the display and display wiring. If the display and wiring are OK, replace the controller.
Why is the compressor of my Airwell PNX009 Air Conditioner overheating and not generating capacity?
If your Airwell Air Conditioner's compressor is overheating and the unit isn't generating capacity, it could be due to: * EEV problem: Check EEV. * Refrigerant leakage: Check the refrigeration system. * Indoor coil block: Clean filters and/or remove the block. * Outdoor coil block: Remove the block and/or avoid air by-pass.
What to do if Airwell PNX009 indoor fan doesn't start?
If the indoor fan of your Airwell Air Conditioner isn't starting, but the louvers are open and the green LED is on, consider these possibilities: * If the unit is in heat mode, the coil may not be warm yet: Change to cool mode. * The outdoor unit may be in the opposite mode: Change the operation mode. * There could be a problem with the controller or capacitor: Change to high speed and check if the power supply to the motor is higher than 130VAC (for triack controlled motor) or higher than 220VAC for fixed speed motors, if OK replace capacitor, if not OK replace controller.
Why does my Airwell PNX009 Air Conditioner compressor stop during operation?
If the compressor of your Airwell Air Conditioner stops during operation, it could be due to: * Electronic control issues. * Refrigerant leakage: Check the refrigeration system.
Why are the display board and LEDs off on my Airwell PNX009 outdoor unit?
If the display board and LEDs are off on your Airwell Air Conditioner outdoor unit, it could be due to: * No power supply: Check the connections and the wiring on the main terminal and repair if needed. Also, check the PFC choke connection and repair if needed. * PFC Chock coil. * Burnt fuse: Check the 25A fuse on the Filter.
What causes Airwell PNX009 units to operate in cool mode with no capacity and others to have water leaks?
If one or more Airwell Air Conditioner indoor units are operating in cool mode without capacity, and other units have water leaks or freezing problems, the communication wires of the indoor units may be switched. Check and correct the communication wire connections.
General| Type | Split System |
|---|---|
| Cooling power | 2.6 kW |
| Cooling Capacity | 9000 BTU/h |
| Refrigerant | R410A |
| Weight (Indoor Unit) | 8.5 kg |
| Power Supply | 220-240V/50Hz |
Technical specifications for the YAZ3 24 DCI outdoor unit.
Technical specifications for the QUATTRO YAZ4 30 DCI outdoor unit.
Detailed specifications for various indoor units including PNX, CK, SX, DLF, XLF, DLS, PRIME, HAD series.
Cooling/heating performance for YAZ3 24 DCI with various indoor unit combinations.
Cooling/heating performance for YAZ4 30 DCI with various indoor unit combinations.
Detailed wiring diagram for YAZ3 24 and YAZ4 30 DCI outdoor units.
Describes how to access and perform the installation test, including fault interpretation.
Common system failures, probable causes, and recommended corrective actions.
To Next Page