EasyManua.ls Logo

Aiwa NSX-R70 - Deck Adjustments and CD Test Mode

Aiwa NSX-R70
58 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
– 43 –
<DECK Section>
10. Tape Speed Adjustment (DECK2)
Requirements
Measuring instrument: Wow and flutter meter (frequency counter)
Test tape: TTA-100(3KHz)
Test point: HP OUT
Adjustment point: SFR1
1) Connect the wow and flutter meter to HP OUT of the unit.
2) Insert the test tape (TTA-100) to DECK 2. Play back the middle part of the tape,
and adjust SFR1 so that the level 3,000Hz±5Hz is monitored.
11. Tape Speed Check (DECK 1)
Requirements: Same as the above, 10.
1) Insert the test tape (TTA-100) to DECK 1. Play back the middle part of the tape, and check that
the level is ranged within ±55Hz as compared to the speed monitored for DECK 2.
12. Wow and Flutter Check (DECK1 and DECK2)
Requirements: Same as the above, 10.
1) Connect the wow and flutter meter to HP OUT of the unit.
2) Set the wow and flutter to JIS for INDICATOR and to W RMS (WTD) for mode.
3) Play back the middle part of the test tape (TTA-100), and check that the level ranges under 0.15%.
13. Head Azimuth Adjustment (DECK1 and DECK2)
Requirements
Measuring instrument: Oscilloscope
Test tape: TTA-300(10KHz)
Test point: TP8(Lch), TP9(Rch)
Adjustment point: Head azimuth adjustment screw
1) Connect the probe CH1 of the oscilloscope to TP8 (Lch) and CH2 to TP9 (Rch).
2) Set V mode of the oscilloscope to ADD.
3) Insert the test tape (TTA-300) to DECK1. Forward and play back the middle part of the tape,
and adjust the head azimuth adjustment screw so that the waveform achieves its maximum level
when 10KHz is played.
4) After adjustment, secure the screw with glue (1600B).
5) Apply the above steps 3) and 4) to DECK2.
14. Playback Frequency Check (DECK1 and DECK2)
Requirements
Measuring instrument: Millivoltmeter
Test tape: TTA-300(315Hz / 10KHz)
Test point: TP8(Lch), TP9(Rch)
1) Connect CH1 of the millivoltmeter to TP8 (Lch) and CH2 to TP9 (Rch).
2) Insert the test tape (TTA-300) to DECK1, and play back 315Hz and 10KHz.
3) Check that the level of 10KHz is ranged within ±3dB compared to the output level of 315Hz
as a reference.
4) Apply the above steps 2) and 3) to DECK2.
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com

Related product manuals