14 | Alarm.com Hub Install Guide Alarm.com Hub Install Guide | 15
Regulatory & CerticationsRegulatory & Certications
Changes or modications not expressly approved by
Alarm.com can void the user’s authority to operate
the equipment.
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment
o and on, the user is encouraged to try to correct
the interference by one or more of the following
measures:
• Re-orient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment to an outlet on a circuit
dierent from that which the receiver is connected
• Consult the dealer or an experienced radio/TV
technician for help.
This equipment complies with the FCC RF radiation
exposure limits set forth for an uncontrolled
environment. This equipment should be installed and
operated with a minimum distance of 20 centimeters
between the radiator and your body.
Under Industry Canada regulations, this radio
transmitter may only operate using an antenna of a
type and maximum (or lesser) gain approved for the
transmitter by Industry Canada.
Conformément à la réglementation d’Industrie
Canada, le présent émetteur radio peut fonctionner
avec une antenne d’un type et d’un gain maximal
(ou inférieur) approuvé pour l’émetteur par Industrie
Canada.
This device complies with Industry Canada licence-
exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not
cause interference, and (2) this device must accept
any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie
Canada applicables aux appareils radio exempts
de licence. L’exploitation est autorisée aux deux
conditions suivantes : (1) l’appareil ne doit pas
produire de brouillage, et (2) l’utilisateur de l’appareil
doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.,
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
FCC ID: YL6143NK100T
IC: 9111A-143NK100T
Hub Specications
Power Requirements 5V nominal
Standby current 90mA (45mA in PowerSave Mode)
Peak Current 1.5 A
Max. Voltage Protection 28V
Operating Voltage 4.6V - 5.53V
Operating Temperature 32 to 120°F (0 to 49°C)
Storage Temperature -30 to 140°F (-34 to 60°C)
Max. Relative Humidity 90% non-condensing
Module Dimensions 13.75 cm x 14.25 cm
Housing Dimensions 16 cm x 16 cm
Cellular Network Dual Band CDMA/1xRTT (3G) or
Dual Band HSPA 2G/3G (850/1900 MHz)
Battery Specications
Type Lithium Ion
Rated Capacity 1300 mAh
Charging Temperature 0 to 45°C
Discharge Temperature -20 to 60°C
Storage Temperature 1 year at +15 to +35°C
1 month at -20 to +60°C
3 months at -20 to +45°C
Max. Relative Humidity 65 ± 20%
Listings UL 1642
To Next Page
Loading...
Need help?
General
