Allen-Bradley 22A-A4P5N104

Quick Start
PowerFlex 4 Adjustable
Frequency AC Drive
FRN 2.xx
This Quick Start guide summarizes the basic steps needed to install,
start-up and program the PowerFlex 4 Adjustable Frequency AC Drive.
The information provided Does Not
replace the User Manual and is
intended for qualified drive service personnel only.
For detailed PowerFlex 4 information including EMC instructions,
application considerations and related precautions refer to the
PowerFlex 4 User Manual , Publication 22A-UM001x on the CD
supplied with the drive or at
www.ab.com/manuals/dr.
General Precautions
!
ATTENTION: The drive contains high voltage capacitors which take
time to discharge after removal of mains supply. Before working on
drive, ensure isolation of mains supply from line inputs [R, S, T (L1,
L2, L3)]. Wait three minutes for capacitors to discharge to safe voltage
levels. Failure to do so may result in personal injury or death.
Darkened display LEDs is not an indication that capacitors have
discharged to safe voltage levels.
!
ATTENTION: Equipment damage and/or personal injury may result
if this parameter (A092 [Auto Rstrt Tries], A094 [Start At PowerUp]) is
used in an inappropriate application. Do not use this function without
considering applicable local, national and international codes,
standards, regulations or industry guidelines.
!
ATTENTION: Only qualified personnel familiar with adjustable
frequency AC drives and associated machinery should plan or
implement the installation, start-up and subsequent maintenance of the
system. Failure to comply may result in personal injury and/or
equipment damage.
!
ATTENTION: This drive contains ESD (Electrostatic Discharge)
sensitive parts and assemblies. Static control precautions are required
when installing, testing, servicing or repairing this assembly.
Component damage may result if ESD control procedures are not
followed. If you are not familiar with static control procedures,
reference A-B publication 8000-4.5.2, “Guarding Against Electrostatic
Damage” or any other applicable ESD protection handbook.
!
ATTENTION: An incorrectly applied or installed drive can result in
component damage or a reduction in product life. Wiring or application
errors, such as, undersizing the motor, incorrect or inadequate AC
supply, or excessive ambient temperatures may result in malfunction of
the system.
Allen-Bradley Drives

Allen-Bradley 22A-A4P5N104 Specifications

General

Model	22A-A4P5N104
Analog Inputs	1
Communication Ports	RS-485
Output Current	4.0A
Amperage	4.0A
Enclosure	IP20
Operating Temperature	0°C to 55°C
Storage Temperature	-40°C to 85°C
Humidity	5…95% noncondensing
Phase	Single
Control Method	V/f Control

Summary

General Precautions

High Voltage Capacitor Discharge Warning

Warns about residual voltage in capacitors after power removal and required discharge time.

Qualified Personnel Requirement

States that only qualified personnel should install, start-up, and maintain the drive.

Electrostatic Discharge (ESD) Precautions

Highlights ESD sensitivity and the need for static control procedures during installation and servicing.

Installation and Application Error Risks

Mounting and Environmental Considerations

Mounting Guidelines

Drive Specifications and Ratings

Protective Features

Describes motor protection, over/under voltage, and ride-through fault capabilities.

Power and IO Wiring

Power Wiring Guidelines

Covers wire ratings, terminal block specifications, and input power condition recommendations.

IO Wiring Recommendations

Provides guidelines for I/O wiring, including wire types and terminal block specs.

Control Terminal Block Configuration

IO Terminal Functions

Explains the function of each I/O terminal and its default/programmed behavior.

Wiring Schemes (SRCSNK)

Drive Start-Up Procedure

Pre-Power-Up Checks

Lists essential checks before applying power, including wiring, voltage, and DIP switch settings.

Applying Power

Describes the steps for applying AC power and control voltages to the drive.

Initial Operation

Integral Keypad Operation

Keypad Display and Menu Structure

Keypad LEDs and Status Indicators

Keypad Buttons and Functions

Parameter Navigation and Editing

Viewing Parameters

Editing Parameters

Explains the process of entering program mode, changing values, and saving them.

Basic Program Group Parameters

Motor and Frequency Settings

Control and Speed Reference

Display Group Parameters and Fault Codes

Fault Code Explanations

Lists common fault codes, their descriptions, and basic troubleshooting steps.