PowerFlex 750-Series Products with TotalFORCE Control 11
Rockwell Automation Publication 750-PC100A-EN-P - December 2016
1000 Hp 9 1102 Light 20x…E980 1212 – 1014 – 1600 – 1400 1900 1400 3500 1400 2500 1400 1217 1100 4
980 Normal 1078 1470 901 – 1600 – 1350 1800 1350 3000 1350 2400 1350 1082 1100 4
825 Heavy 1238 1485 759 – 1600 – 1100 1400 1100 2400 1100 2000 1100 911 1100 4
1100 Hp 10 1220 Light 20x…E1K1 1342 – 1122 – 1600 900 1600 2000 1600 3500 1600 3000 1600 1347 1100 6
1045 Normal 1150 1568 961 – 1600 900 1350 1800 1350 3000 1350 2500 1350 1154 1100 6
980 Heavy 1470 1764 901 – 1600 900 1350 1800 1350 3000 1350 2400 1350 1082 1100 6
1250 Hp 10 1430 Light 20x…E1K2 1573 – 1315 – 1600 900 1800 2500 1800 4500 1800 3500 1800 1579 1100 6
1220 Normal 1342 1830 1122 – 1600 900 1600 2000 1600 3500 1600 3000 1600 1347 1100 6
1045 Heavy 1568 1881 961 – 1600 900 1350 1800 1350 3000 1350 2500 1350 1154 1100 6
1500 Hp 10 1624 Light 20x…E1K5 1786 – 1494 – 1600 900 2400 3000 2400 5000 2400 4000 2400 1793 1100 6
1430 Normal 1573 2145 1315 – 1600 900 1800 2500 1800 4500 1800 3500 1800 1579 1100 6
1220 Heavy 1830 2196 1122 – 1600 900 1600 2000 1600 3500 1600 3000 1600 1347 1100 6
2000 Hp 11 2146 Light 20x…E2K0 2361 – 1974 1600 1600 – 3000 3800 3000 6000 3000 5000 3000 2369 1100 8
1946 Normal 2141 2919 1790 1600 1600 – 2500 3500 2500 6000 2500 5000 2500 2148 1100 8
1700 Heavy 2550 3060 1564 1600 1600 – 2400 3000 2400 5000 2400 4500 2400 1877 1100 8
2500 Hp 12 2668 Light 20x…E2K4 2935 – 2454 1600 1600 900 3500 4500 3500 6000 3500 6000 3500 2946 1100 10
2420 Normal 2662 3630 2226 1600 1600 900 3500 4000 3500 6000 3500 6000 3500 2672 1100 10
2070 Heavy 3105 3726 1904 1600 1600 900 3000 3500 3000 6000 3000 5000 3000 2285 1100 10
(1) ‘Applied Rating’ refers to the motor that will be connected to the drive. For example, a ‘E355’ drive can be used in Normal Duty mode on a 350 Hp motor, in Heavy Duty mode on a 300 Hp motor or in Light Duty mode on a 400 Hp motor. The drive can be programmed for each mode. Wiring and fuses can be sized
based on the programmed mode. For any given drive catalog number, Normal Duty mode provides higher continuous current but smaller overload current with respect to Heavy Duty mode. See parameter 306 [Duty Rating].
Refer to Specifications for an explanation of Duty Ratings.
(2) These AC line fuses (with blown fuse indicators) are included in the drive to provide drive short circuit protection. AC input protection devices for branch circuit protection based on US NEC are listed in the table. Each LCL filter has one fuse per phase.
(3) Minimum protection device size is the lowest rated device that supplies maximum protection without nuisance tripping.
(4) Maximum protection device size is the highest rated device that supplies drive protection. For US NEC, minimum size is 125% of motor FLA. Ratings shown are maximum.
(5) Circuit Breaker - inverse time breaker. For US NEC, minimum size is 125% of motor FLA. Ratings shown are maximum.
(6) Recommended Motor circuit protector - Instantaneous trip circuit breaker. The trip setting should be set to the input current of the drive and should be sized for the continuous current of the system.
(7) These DC line fuses (with blown fuse indicators) are included in the drive to provide drive short circuit protection.
600 Volt AC and 810 Volt DC Input Protection Devices - Frames 8…12 (continued)
600 Volt AC Input 810 Volt DC Input
Applied
Rating
(1)
Frame
Cont.
Output
Amps
Duty
Catalog
Number
Output
Overload Amps
Continuous
AC Input
AC Input Integral
Semiconductor Fuse
Size
(170M Type)
(2)
AC Input Protection Devices
Input
Quantities
DC Input
Integral
Semiconductor
Fuse Kit
(7)
Dual Element Time
Delay Fuse
Non-Time Delay Fuse Circuit Breaker
(5)
Motor Circuit
Protector
(6)
Continuous
DC Input
(x = G or J) 1 min 3 sec Amps 2xLCL
Amps
2xLCL
Amps
1xLCL
Amps
1/Phase
Min
(3)
Max
(4)
1/Phase
Min
(3)
Max
(4)
Min Max Amps Amps Qty.
To Next Page
Loading...
Need help?
General
