1. Control must be in Manual Mode. Refer to How to Enter the
Manual Mode.
2.
Press the DELICATE (∧) or the HOT (∨) keypad until Prog
appears in the display. Press the START (enter) keypad, and
AtS 1 will appear in the display.
3. Press the DELICATE (∧) or the HOT (∨) keypad to scroll
through the programmable options until CNP- appears in the
display.
4.
When CNP- appears in the display, press the START (enter)
keypad.
5. Press the DELICATE (∧) or the HOT (∨) keypad to scroll
through the programmable options until CNP 4 appears in the
display.
6.
When CNP 4 appears in the display, press the START (enter)
keypad. A number will appear in the display corresponding to
the number of minutes to be added to agitate steps that have
wash selected as their status.
7. Press the DELICATE (∧) or the HOT (∨) keypad to increase
or decrease the current number minutes.
8. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
How to Program Cycle Modifier DELUXE
Additional Rinse Time CNP 5
This option allows the owner to add additional time to agitate
steps that have Rinse 1 selected as their status. The additional
rinse time option needs to be turned on for the Cycle Modifier
DELUXE Additional Rinse Time to take effect.
1. Control must be in Manual Mode. Refer to How to Enter the
Manual Mode.
2.
Press the DELICATE (∧) or the HOT (∨) keypad until Prog
appears in the display. Press the START (enter) keypad, and
AtS 1 will appear in the display.
3. Press the DELICATE (∧) or the HOT (∨) keypad to scroll
through the programmable options until CNP- appears in the
display.
4.
When CNP- appears in the display, press the START (enter)
keypad.
5.
When CNP 5 appears in the display, press the START (enter)
keypad. A number will appear in the display corresponding to
the number of minutes to be added to steps that have Rinse 1
selected as their status.
6. Press the DELICATE (∧) or the HOT (∨) keypad to increase
or decrease the current number of minutes.
NOTE: To go back to the current programmable op-
tion without changing the value, press the WARM (<)
keypad.
7. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
How to Program Cycle Modifier ULTRA Additional
Wash Time CNP 6
This option allows the owner to add additional time to agitate
steps that have wash selected as their status. The additional wash
time option needs to be turned on for the Cycle Modifier ULTRA
Additional Wash Time to take effect.
1. Control must be in Manual Mode. Refer to How to Enter the
Manual Mode.
2.
Press the DELICATE (∧) or the HOT (∨) keypad until Prog
appears in the display. Press the START (enter) keypad, and
AtS 1 will appear in the display.
3. Press the DELICATE (∧) or the HOT (∨) keypad to scroll
through the programmable options until CNP- appears in the
display.
4.
When CNP- appears in the display, press the START (enter)
keypad.
5. Press the DELICATE (∧) or the HOT (∨) keypad to scroll
through the programmable options until CNP 6 appears in the
display.
6.
When CNP 6 appears in the display, press the START (enter)
keypad. A number will appear in the display corresponding to
the number of minutes to be added to steps that have Wash se-
lected as their status.
7. Press the DELICATE (∧) or the HOT (∨) keypad to increase
or decrease the current number of minutes.
8. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
How to Program Cycle Modifier ULTRA Additional
Rinse Time CNP 7
This option allows the owner to add additional time to agitate
steps that have Rinse 1 selected as their status. The additional
rinse time option needs to be turned on for the Cycle Modifier
ULTRA Additional Rinse Time to take effect.
1. Control must be in Manual Mode. Refer to How to Enter the
Manual Mode.
2.
Press the DELICATE (∧) or the HOT (∨) keypad until Prog
appears in the display. Press the START (enter) keypad, and
AtS 1 will appear in the display.
3. Press the DELICATE (∧) or the HOT (∨) keypad to scroll
through the programmable options until CNP- appears in the
display.
4.
When CNP- appears in the display, press the START (enter)
keypad.
5. Press the DELICATE (∧) or the HOT (∨) keypad to scroll
through the programmable options until CNP 7 appears in the
display.
6.
When CNP 7 appears in the display, press the START (enter)
keypad. A number will appear in the display corresponding to
Programming Control
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
74 Part No. 807870ENR3
To Next Page
Loading...
