machine. If the control is in Start Mode, the cycle time will be
displayed. Pressing the START keypad will start the machine cy-
cle. Once a machine cycle has been started, each additional press
of the START keypad will advance the cycle to the next cycle
step only if Rapid Advance Programming Parameter is Enabled.
1. Control must be in Manual Mode. Refer to How to Enter the
Manual Mode.
2.
Press the DELICATE (∧) or the HOT (∨) keypad until Prog
appears in the display. Press the START (enter) keypad, and
AtS 1 will appear in the display.
3. Press the DELICATE (∧) or the HOT (∨) keypad to scroll
through the programmable options until oPL- appears in the
display.
4.
When oPL- appears in the display, press the START (enter)
keypad to enter the OPL submenu.
5. Press the DELICATE (∧) or the HOT (∨) keypad to scroll
through the programmable options until oPL 1 appears in the
display.
6.
When oPL 1 appears in the display, press the START (enter)
keypad. The current OPL status will appear in the display.
on = Option Enabled
oFF = Option Disabled (factory default setting)
7. Press the DELICATE (∧) or the HOT (∨) keypad to change
the current status.
8. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
OPL Delayed Start oPL 2
This option allows the owner to enable delayed start mode which
can delay the cycle up to a maximum of 72 hours.
1. Control must be in Manual Mode. Refer to How to Enter the
Manual Mode.
2.
Press the DELICATE (∧) or the HOT (∨) keypad until Prog
appears in the display. Press the START (enter) keypad, and
AtS 1 will appear in the display.
3. Press the DELICATE (∧) or the HOT (∨) keypad to scroll
through the programmable options until oPL- appears in the
display.
4.
When oPL- appears in the display, press the START (enter)
keypad to enter the OPL submenu.
5. Press the DELICATE (∧) or the HOT (∨) keypad to scroll
through the programmable options until oPL 2 appears in the
display.
6.
When oPL 2 appears in the display, press the START (enter)
keypad. The current OPL status will appear in the display.
on = Option Enabled
oFF = Option Disabled (factory default setting)
7. Press the DELICATE (∧) or the HOT (∨) keypad to change
the current status.
8. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
OPL Display Power Save oPL 3
This option allows the owner to enable the OPL Display Power
Save Feature. If enabled, after 255 seconds of no user input, the
control will turn off all LEDs and the display until user input oc-
curs. The OPL Display Power Save Feature will only turn off the
display if the control is in Start Mode.
1. Control must be in Manual Mode. Refer to How to Enter the
Manual Mode.
2.
Press the DELICATE (∧) or the HOT (∨) keypad until Prog
appears in the display. Press the START (enter) keypad, and
AtS 1 will appear in the display.
3. Press the DELICATE (∧) or the HOT (∨) keypad to scroll
through the programmable options until oPL- appears in the
display.
4.
When oPL- appears in the display, press the START (enter)
keypad to enter the OPL submenu.
5. Press the DELICATE (∧) or the HOT (∨) keypad to scroll
through the programmable options until oPL 3 appears in the
display.
6.
When oPL 3 appears in the display, press the START (enter)
keypad. The current OPL status will appear in the display.
on = Option Enabled
oFF = Option Disabled (factory default setting)
7. Press the DELICATE (∧) or the HOT (∨) keypad to change
the current status.
8. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Drop Off Mode droP
This option allows the owner to limit machine use to an attendant
without requiring vend. Refer to Drop-Off Mode for more details.
1. Control must be in Manual Mode. Refer to How to Enter the
Manual Mode.
2.
Press the DELICATE (∧) or the HOT (∨) keypad until Prog
appears in the display. Press the START (enter) keypad, and
AtS 1 will appear in the display.
3. Press the DELICATE (∧) or the HOT (∨) keypad to scroll
through the programmable options until droP appears in the
display.
4.
When droP appears in the display, press the START (enter)
keypad. The current Drop Off Mode status will appear in the
display.
on = Option Enabled
oFF = Option Disabled (factory default setting)
Programming Control
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
92 Part No. 807870ENR3
To Next Page
Loading...
