To Next PageTo Next Page
What to do if Alliance Laundry Systems Dryer has spark but no flame?
If your Alliance Laundry Systems Dryer has a spark but no flame, first ensure the gas is on. Also, check for 24 VAC at the gas valve. If the issue persists, there might be a problem with the control; in this case check the voltage between the gas valve terminal MV and GND on the control.
Why Alliance Laundry Systems UT055N Dryer valve is on but there is no spark during TFI?
If the valve is on but there's no spark during TFI in your Alliance Laundry Systems Dryer, it could be due to a shorted electrode. Another possible cause is an incorrect spark gap; ensure it's set to .094-.156 inch. Also, inspect the high voltage cable for faults or poor connections. Finally, control failure can cause this issue.
What to do if Alliance Laundry Systems Dryer flame is okay during TFI, but no flame sense after TFI?
If the flame is okay during TFI but there's no flame sense after TFI in your Alliance Laundry Systems Dryer, check the electrode position and cleanliness. Also, inspect the high voltage wire. Poor grounding at the burner or a poor flame (check flame current) can also cause this issue.
How to fix reset failure on Alliance Laundry Systems UT055N Dryer?
If you're experiencing a reset failure on your Alliance Laundry Systems Dryer, it might be because the reset switch was pressed too long; try resetting again. Another possibility is that the reset switch is shorted, in which case you should replace the switch.
What to do if Alliance Laundry Systems UT055N thermostat is on, but there is no spark or valve?
If the thermostat is on but there's no spark or valve activity in your Alliance Laundry Systems Dryer, first ensure the cable connects to the control and electrode, and that voltage is present at the gas valve. If the issue persists, the control might be bad; check the red LED for a steady on or flashing codes.
How to reset Alliance Laundry Systems Dryer control in lockout mode?
If the control in your Alliance Laundry Systems Dryer is in lockout mode, a manual reset is needed. Reset it by pushing the red lockout button or use the front end control.
What to do if the Alliance Laundry Systems UT055N Dryer control is in lockout mode?
If the control panel on your Alliance Laundry Systems Dryer is in lockout mode, you will need to manually reset it. You can do this by pushing the red lockout button or using the front end control.
General| Brand | Alliance Laundry Systems |
|---|---|
| Model | UT055N |
| Category | Dryer |
| Type | Tumble Dryer |
| Capacity | 55 lb |
| Heat Source | Gas |
| Drum Material | Stainless Steel |
| Control Type | Electronic |
| Voltage | 208/240V |
General warnings regarding safety, gas, and electrical hazards.
Specific installation rules for appliances in Massachusetts, USA.
Overview of tumble dryer models and capacities.
Keep instructions for future reference and include with machine ownership change.
Information applicable to various gas, steam, and electric tumble dryer models.
Details for contacting Alliance Laundry Systems for service and parts.
Explains DANGER, WARNING, CAUTION, IMPORTANT, and NOTE statements.
Basic precautions to reduce risk of fire, electric shock, injury, or death.
Detailed safety advice covering materials, operation, maintenance, and user responsibility.
Includes noise level, weight, packaging, dimensions, motor, and fan specifications.
Detailed cabinet dimensions for 025, 030, 035, and 055 series models.
Detailed cabinet dimensions for T30 and T45 series models.
Specifies exhaust outlet diameters and positions for 025-055 series.
Specifies exhaust outlet diameters and positions for T30 and T45 series.
Details gas connection points (A, B, C) for 025-055 series models.
Details gas connection points (A, B, C) for T30 and T45 series models.
Specifies electrical connection points (A, B, C, D) for 025-055 series models.
Specifies electrical connection points (A, B, C, D, E) for T30 and T45 series models.
Details steam connection points (A, C inlet; B, D outlet) for 025-035 series.
Details steam connection points (A, C inlet; B, D outlet) for T30 series.
Visual inspection of crate and parts upon delivery for shipping damage.
Guidelines for selecting an appropriate installation location for the dryer.
Instructions on how to properly position and level the tumble dryer using its legs.
Instructions for installing and adjusting the fifth leveling leg for stability.
Warnings and requirements related to the fire suppression system.
Specifies water pressure, flow rate, and temperature needed for the fire suppression system.
Procedure for connecting water supply hoses to the tumble dryer.
Warnings and notes regarding electrical power supply and connections.
Final checks and preparations before operating the tumble dryer after installation.
Specific items to complete once a CE model machine is installed.
Information for installing gas dryers in CE countries with different gas types.
Steps to convert the machine configuration for different gas types or pressures.
Detailed procedures for converting gas valves and burner orifices.
Guidance on sizing gas supply pipes and installing loops for equal pressure.
Tables providing orifice sizes for different altitudes and gas types.
Warnings about combustible lint, plastic/foil ducts, and improper exhaust locations.
Guidelines for dryer layout and ensuring adequate make-up air supply.
Recommendations for safe and efficient exhaust venting, avoiding static pressure.
Specifications for exhaust duct materials, construction, and clearances.
Guidelines for individual exhaust duct sizing and length limitations.
Requirements for sizing and installing a common manifold exhaust system.
Warnings regarding gas connection, leaks, and LP gas venting.
Specifies required natural gas and LP gas pressures for operation.
Part numbers for converting non-CE models from natural to L.P. gas.
Guidance on sizing gas supply pipes and installing loops for equal pressure.
Tables providing orifice sizes for different altitudes and gas types.
Warnings about shock, fire, proper grounding, and three-phase connections.
Instructions for connecting central pay systems to specific control suffixes.
Requirements for electrically grounding the tumble dryer for safety.
Identifies locations for ground screws and terminal blocks on various models.
Step-by-step procedure for connecting electrical service to the tumble dryer.
Guidance on converting tumble dryers for different service voltages.
Specific electrical connection requirements for T30 and T45 series models.
Detailed steps for converting voltage configurations on specific models.
Procedure for installing ferrite rings to protect electronic controls.
Electrical specs including voltage, amps, breaker rating, and wire size for 025-035 series.
Electrical specs including voltage, amps, breaker rating, and wire size for T30 series.
Electrical specs including voltage, amps, breaker rating, and wire size for T45 series.
Electrical specs for 21 kW Classic Line 030 Series electric models.
Electrical specs for 21 kW Classic Line T30 Series electric models.
Electrical specs for 24 kW Classic Line 035 Series electric models.
Electrical specs for 12 kW Eco Line 035 Series electric models.
Electrical specs for 27 kW Classic Line 055 Series electric models.
Electrical specs for 18 kW Eco Line 055 Series electric models.
Specifies steam pressure and pipe sizing requirements for optimal operation.
Recommendations for steam supply and return line piping, including traps and insulation.
Procedure for installing steam traps and connecting condensate return lines.
Describes the control's behavior when power is first applied.
State where the control waits for a vend to be satisfied.
State after vend is satisfied but before the start button is pressed.
The state when the machine is actively running a cycle.
Control behavior when the loading door is opened during a cycle.
State after the cycle is complete and the IN USE LED is off.
Instructions for programming dry and cool down times using dipswitches.
Procedure to reset accumulated cycle time on the control.
How the control handles additional coin drops during a cycle.
Diagnostic feature to test temperature selector settings via IN USE LED.
Steps to program and test a short cycle using dipswitches.
Displays and corrective actions for error code AF (flashing).
Warnings about drying specific materials and cleaning the lint screen.
Operation of the emergency stop button on CE approved models.
Procedure for loading laundry and maximum load capacities.
Guidance on selecting temperature based on fabric care labels.
Instructions for removing laundry after cycle completion.
Explanation of the cylinder reversing feature and how to select it.
Overview of different control types and their basic functions.
How to set heat time, cool down time, and temperature on dual timer controls.
Warnings about removing laundry immediately during power failure and anti-wrinkle features.
Operation of the Electronic OPL Micro Control for automatic, time dry, or custom cycles.
Instructions for operating the MDC control using coin or card payment.
Operation of the Quantum control for selecting cycles and inserting payment.
Operation of the Galaxy 600 control for selecting cycles and inserting payment.
Operation of the LED OPL control for changing cycles and starting the dryer.
Control panel layouts and operation for S, H, U, and Y model series.
Operation of the UniLinc control for selecting and customizing cycles.
Operation of the DX4 Coin control for selecting cycles and inserting coins.
Operation of the DX4 OPL control for selecting cycles.
General operation and default programs of the DMP control.
How to program custom cycles and settings for the DMP control.
How to set and adjust reversing times for the cylinder.
Information on the function and proper setup of the rotation sensor.
Features related to safety tumble and anti-wrinkle cycles.
Operational checks for board diagnostics and error indicators.
Description of the OPL control panel and its functions.
Explains the function of each DIP switch on the DMP control.
Operation and programming of the DMP coin control for run time and temperature.
Details ignition control operation and troubleshooting for models from 3/11/13.
Lists LED indications and corresponding fault modes for the ignition control.
Common symptoms and probable causes for operational issues.
Importance of correct electrode placement for optimal system performance.
How to measure flame current using a multimeter for proper sensing.
Explanation of ignition sequence, modes, and lockout for non-CE models.
Explanation of ignition sequence, modes, and lockout for CE models.
Interpretation of diagnostic LED status and error codes.
How to adjust the air shutter for proper combustion and efficiency.
Information on the airflow switch operation and importance for safety.
How to adjust the loading door switch for proper operation.
How to adjust the door strike for proper door tension and closure.
Tasks to perform daily, including inspecting the area and cleaning the lint screen.
Tasks to perform monthly, such as cleaning the exhaust duct.
Tasks to perform quarterly, including cleaning air vents and steam coils.
Tasks to perform bi-annually, such as checking hardware and connections.
Tasks to perform annually, like removing the cylinder for cleaning.
Procedure for testing the fire suppression system every three months.
Troubleshooting guide for common issues before contacting service personnel.
Steps to safely disconnect and remove the tumble dryer from service.
Information on proper disposal of the appliance according to WEEE directive.
