To Next PageTo Next Page
Need help?Do you have a question about the Alliance Laundry Systems UT075L and is the answer not in the manual?
General| Brand | Alliance Laundry Systems |
|---|---|
| Model | UT075L |
| Category | Dryer |
| Type | Commercial |
| Capacity | 75 lbs |
| Drum Material | Stainless Steel |
| Control Type | Microprocessor |
| Heat Source | Gas or Electric |
Lists models applicable to this manual.
Details the machine's nameplate and accessing Machine ID.
Explains the UniLinc control's features and capabilities.
Instructions for correctly configuring DIP switches.
Describes control behavior during power outages.
Details communication capabilities with PDAs and networks.
Lists types of audit data collected and accessible.
Menu for IR communication with PDAs.
Displays error messages for IR communication issues.
Resets control settings and cycles to factory defaults.
Steps to enter the system menu for programming.
Describes the functions of the seven control keypads.
Explains the different operational states of the control.
Mode for displaying fatal machine errors.
Mode for control communication with PDA or network.
Mode after heat segment or fatal error.
Mode after cool down segment finishes.
Mode for anti-wrinkle and delayed tumbling.
Describes cylinder rotation for reversing models.
How to enter diagnostic tests from Idle Mode.
How the control runs cycle segments sequentially.
Regulates temperature and time as programmed.
Determines cycle time based on dryness level.
Uses sensor data for moisture control.
Monitors cylinder rotation for errors.
Provides cycle and segment info during operation.
Displays when loading or lint door is open.
Allows adjustment of contrast and backlight.
Accesses diagnostic info for the running cycle.
Displays detailed operating data and allows adjustments.
Displays when a cycle is stopped or aborted.
Displays when a cycle or menu has an error.
Displayed before a cycle completes.
Appears after a programmed number of cycles.
Prompts user on whether the basket is empty.
Indicates moisture sensor may need servicing.
Overview of control navigation features.
How to navigate between different menus.
Navigating when a menu spans multiple pages.
Navigating and changing modifiable parameters.
Editing cycle names and banners.
Refers to charts of display menu maps.
Visual representation of the system menu structure.
Visual representation of the run menu structure.
Visual representation of the service menu structure.
Accessing cycle programming, diagnostics, and laundry management.
Confirms programming changes before saving.
Used to program cycles.
Menu for programming individual cycles.
Chart of characters for cycle name editing.
Illustrates the programming process.
Navigating within segment menus.
Allows changes to global machine properties.
Selects the displayed language for menus.
Sets date, day, time, and daylight saving.
Creates or modifies banners displayed on the Cycle Menu.
Option to enable rapid advance through segments.
Sets audio feedback, beeper volume, and external signal.
Configures multi-segment cycles and lint screen reminders.
Sets heater error retry attempts.
Sets global temperatures and units.
Sets rotate/stop times for reverse cylinder.
Sets Cool Down target temperature and time.
Enables/disables moisture dry options and error display.
Resets parameters to factory default settings.
Contains Test, Alarm, and Machine ID menus.
Features for manufacturing and service testing.
Used to run several test steps and a ten-minute cycle.
Details steps for test cycle execution.
Manual control of outputs and display of inputs.
Provides information on recent and counted alarms.
Displays manufacturing and machine information.
Error during communication with a PDA.
Error during network communication.
Error due to temperature below threshold.
Error due to temperature above threshold.
Errors related to temperature limit thermostats.
Errors related to gas ignition.
Errors related to airflow switch functionality.
Error when rotation sensor detects zero RPM.
Errors related to moisture sensing system.
Error when fan motor contactor is not sensed closed.
Error when fan motor centrifugal switch fails to close.
Error due to mismatch in DIP switch config.
Contains three screens for cycle counts and run hours.
Provides a time-based service reminder list.
Lists daily service reminders.
Lists monthly service reminders.
Lists service reminders performed quarterly.
Lists service reminders performed twice a year.
Details for standard machine cycles.
Lists details for wetclean machine cycles.
