What to do if Alliance Laundry Systems UT055E has spark but no flame?
If your Alliance Laundry Systems Dryer has a spark but no flame, first ensure the gas is on. Also, check for 24 VAC at the gas valve. If the issue persists, there might be a problem with the control; in this case check the voltage between the gas valve terminal MV and GND on the control.
Why Alliance Laundry Systems Dryer valve is on but there is no spark during TFI?
If the valve is on but there's no spark during TFI in your Alliance Laundry Systems Dryer, it could be due to a shorted electrode. Another possible cause is an incorrect spark gap; ensure it's set to .094-.156 inch. Also, inspect the high voltage cable for faults or poor connections. Finally, control failure can cause this issue.
What to do if Alliance Laundry Systems UT055E flame is okay during TFI, but no flame sense after TFI?
If the flame is okay during TFI but there's no flame sense after TFI in your Alliance Laundry Systems Dryer, check the electrode position and cleanliness. Also, inspect the high voltage wire. Poor grounding at the burner or a poor flame (check flame current) can also cause this issue.
How to fix reset failure on Alliance Laundry Systems UT055E?
If you're experiencing a reset failure on your Alliance Laundry Systems Dryer, it might be because the reset switch was pressed too long; try resetting again. Another possibility is that the reset switch is shorted, in which case you should replace the switch.
What to do if Alliance Laundry Systems UT055E Dryer thermostat is on, but there is no spark or valve?
If the thermostat is on but there's no spark or valve activity in your Alliance Laundry Systems Dryer, first ensure the cable connects to the control and electrode, and that voltage is present at the gas valve. If the issue persists, the control might be bad; check the red LED for a steady on or flashing codes.
How to reset Alliance Laundry Systems UT055E control in lockout mode?
If the control in your Alliance Laundry Systems Dryer is in lockout mode, a manual reset is needed. Reset it by pushing the red lockout button or use the front end control.
What to do if the Alliance Laundry Systems UT055E Dryer control is in lockout mode?
If the control panel on your Alliance Laundry Systems Dryer is in lockout mode, you will need to manually reset it. You can do this by pushing the red lockout button or using the front end control.
Details on model numbers and their configurations.
Critical safety precautions for operation and installation.
Physical measurements for dryer models.
Location details for dryer exhaust ports.
Gas connection points for various dryer models.
Electrical connection points for various dryer models.
Steam connection points for various dryer models.
Steps to inspect the unit before installation.
Guidelines for choosing a suitable installation location.
Instructions for properly positioning and leveling the dryer.
Details on water supply for the fire suppression system.
Guidance on sizing and looping gas supply pipes.
Procedures for sizing burner orifices at high altitudes.
Procedures for proper electrical grounding.
Steps for connecting electrical service to the dryer.
Procedures for converting voltage settings.
Guidelines for steam piping installation.
Steps for installing steam traps and connecting return lines.
How to configure drying time using dipswitches.
Table showing dipswitch configurations for drying time.
Operation of the emergency stop button.
Instructions for using the dual digital timer control.
Operating instructions for the Electronic OPL Micro Control.
Operating instructions for Quantum Control models.
How to adjust the gas burner air shutter for proper flame.
Information and checks for the airflow switch.
Adjustment procedure for the loading door switch.
Routine daily maintenance tasks.
Routine monthly maintenance tasks.
Procedure for testing the fire suppression system.
Troubleshooting steps for when the dryer won't start.
Troubleshooting steps for when the dryer won't heat.
Troubleshooting steps for when clothes are not dry.
General| Brand | Alliance Laundry Systems |
|---|---|
| Model | UT055E |
| Category | Dryer |
| Type | Commercial |
| Capacity | 55 lbs |
| Heat Source | Electric |
| Drum Material | Stainless Steel |
| Control Type | Microprocessor |
| Heating Method | Electric Resistance |
| Voltage | 240V |
| Amperage | 30A |
To Next Page