Alliance Laundry Systems UWN065T4V - Programming Manual

82 pages

Save Page as PDF

To Next Page

Programming

www.comlaundry.com

Washer-Extractor

Pocket Hardmount

UniLinc Control

Refer to Page 9 for Model Identification

PHM14

PHM1423C

Part No. F8434101R1

April 2012

Keep These Instructions for Future Reference.

(If this machine changes ownership, this manual must accompany machine.)

Main Page

Unilinc Control1
Table of Contents3
Safety Information7
Explanation of Safety Messages7
Important Safety Instructions7
Safety Decals9
Operator Safety10
Introduction11
Model Identification11
Nameplate Location12
Replacement Parts12
Customer Service12
Preliminary Information13
About the Control13
- Power Failure Recovery13
- IR Communications13
- Network Communications13
- Audit Information13
- IR Communications Menu14
- IR Communications Error Menu14
- Restore to Factory Defaults14
- Entering Program Mode15
Unilinc Identification16
Operational Keypad16
Operation Modes17
- General Modes of Operation17
- Power-Up Mode17
- Idle Mode17
- Door Locking Mode17
- Run Mode17
- Stop Mode17
- Door Unlocking Mode17
- Error Mode17
- Delayed Start Countdown Mode17
Machine Cycle Definition and Operation18
Machine Cycle Operation18
Delayed Start Feature18
Cycle Menu18
- To Start a Cycle19
Run Menu20
Contrast/Backlight Menu22
Close Door Menu22
Lubricate Bearings Menu23
Run Diagnostic Menu23
Speed, Temp and Water Level Menu24
Cycle Aborted Retry Menu24
Error Menu25
Cycle Stopped Menu25
Delayed Start Menu25
Cycle Aborted Fatal Menu25
Delayed Start Countdown Menu26
Delayed Start Final Countdown Menu26
Menu Navigation27
The Unilinc27
Menu Navigation on a Single Screen27
Menu Navigation with Parameters27
Screen to Screen Navigation Using the Arrow Keypads27
Navigation in String Edit Mode27
Display Screen Maps28
- System Menu Map Tree28
- Run Menu Map Tree29
- Service Menu Map Tree29
Programming Unilinc30
System Menu30
Save Changes Menu30
Program Menu31
Modify Cycle31
- Available Characters32
Cycle, Segment and Step Programming Flow Diagram33
- Step Menu Navigation33
- Reuse Fill Step Menu34
- Fill Step Menu35
- Heater Option36
- Supply a and B Step Menu36
- Agitate Step Menu37
- Cool down Step Menu37
- Drain Step Menu38
- Spray Rinse Extract Step Menu38
- Extract Step Menu39
- General Purpose Signals Menu39
- End of Segment Audio Signal Step Menu40
Global Setup41
Global Setup Menu41
Language Menu41
Date/Time Menu41
Water Level Menu42
Temperature Menu42
Audio Menu43
Balance Retry Menu43
Water Management Menu44
Alarms Program Menu46
Rapid Advance Menu46
Banners Menu47
Factory Defaults Menu47
Shakeout Menu47
Water Level Confirmation Menu48
Water Temperature Confirmation Menu48
Alarms Confirmation Menu48
Audio Confirmation Menu49
Reset All Factory Defaults Confirmation Menu49
Factory Defaults Second Confirmation Menu49
Diagnostic50
Diagnostic Menu50
- Drive ID Menu50
- Drive Alarms Menu50
Test Menu50
- Test Cycle51
Factory Valve Purge Menu53
Inputs Outputs Menu53
Water Leak Detection Diagnostic55
Drive Test55
Alarms56
Machine Identification57
Machine Errors57
- Door Lock Error57
- Door Open Error57
- Drain Alarm Error57
- Fill Alarm Error57
- Frame Balance Switch Error58
- Open Temperature Sensor Error58
- Shorted Temperature Sensor Error58
- SPI Error58
- Unbalance Error58
- Heat Alarm Error58
- Water Level Sensor Error59
- IR Communications Error59
- Network Communications Error59
- Water Leak Detection Error59
- Slow Drain Detected During a Machine Cycle Error60
- Drive SPI Error60
- DC Bus Error60
- No Tachometer Error60
- Locked Rotor Error60
- Shorted IGBT Error60
- IPM Overtemperature Error61
- Invalid Parameter Set Error61
- Maximum Current Exceeded Error61
- Current Sensor Error61
- Low DC Bus Error61
- Invalid Command Error61
- Last Drive Error61
Laundry Management62
Total Number of Machine Cycle Counters63
Total Number of Operating Minutes Counters63
Last 10 Machine Cycles Rapid Advanced or Stopped63
Maintenance64
Service Schedule Menu64
- Daily Menu (Service)64
- Weekly Menu (Service)64
- Monthly Menu (Service)65
- Quarterly Menu (Service)65
Cycle Charts66

Alliance Laundry Systems UWN065T4V - Programming Manual

Table of Contents

Other manuals for Alliance Laundry Systems UWN065T4V

Related product manuals