ALLIANCE SWNNX2SP115CW02 User Manual

Programming
Topload Washer
Refer to Page 9 for Model Identification
TLW25C_SVG
Soil
Cycle
Temp
MEDIUM
Original Instructions
Keep These Instructions for Future Reference.
CAUTION: Read the instructions before using the machine.
(If this machine changes ownership, this manual must accompany machine.)
Part No. 204370ENR1
January 2019

ALLIANCE SWNNX2SP115CW02 Specifications

General

Loading Type	Front Load
Color	White
Brand	Alliance
Model	SWNNX2SP115CW02
Category	Washer
Voltage	120V
Cycle Options	Normal, Delicate, Heavy Duty
Energy Efficiency	Energy Star Certified

Summary

Topload Washer

Testing Machine and Electronic Control Functions

Diagnostic (Testing) Mode – Quick Reference Chart

Error Codes

Transmission Failure (E101)

Time-out Error (E102)

Invalid Command Code (E.03)

Expecting Upload Request (E104)

Power Fail Recovery

Preliminary Information

Power Failure Recovery

How the washer behaves during and after a power failure.

Communications

Methods for communicating with the washer control.

Washer Operation

Washer Operation (continued)

Special Features

Rapid Advance Feature

Allows quick advancement through an active cycle or to Ready Mode.

Clearing the Vend Feature

Resets control if coins entered but vend not satisfied.

Communications Mode

Allows control communication via external device, card reader, or network.

Entering the Manual Mode

How to Enter the Manual Mode

Step-by-step guide to enter Manual Mode.

Manual Mode Navigation

Overview of the five groups within Manual Mode.

Programming Control

What Can Be Programmed

Overview of programmable features and options.

Programmable Options Available

Detailed list of programmable options and their settings.

Programming Control (continued)

Manual Programming Flowchart

Flowchart illustrating manual programming steps for options.

Error Code Parameters Flowchart

Flowchart for programming various error code parameters.

Drain Error Flowchart

Flowchart detailing drain error programming options.

Real Time Clock Programming

Programming options for setting the real-time clock.

Special Vend 1 Parameters

Parameters for configuring Special Vend 1.

Cycle Modifier Programming

Programming options for cycle modifiers.

Cycle Programming

Programming options for cycle parameters like agitation time.

IR Access and Manual Advance

Enabling/disabling IR access and manual advance features.

Vend Price 1 (AtS 1)

Setting vend price for Normal Hot cycle.

Vend Price 5 (AtS 5)

Setting vend price for Perm Press Warm cycle.

Vend Price 9 (AtS 9)

Setting vend price for Delicates Cold cycle.

Coin 1 Value (dEn 1)

Programmable Output Type (AtYPE)

Default Cycle (DFECYC)

How to Read Audio Signal Table

Network Node Number (node)

Error Code Programming Parameters

Details on programming specific error code parameters.

Water Leak Detection Error Menu

Set Real-Time Clock (rtC-)

How to Read the Days Enable Value Table

Special Vend 1 Start Minute (SP1 2)

Setting the start minute for Special Vend 1.

Special Vend 1 Start Year (SP1 6)

Setting the start year for Special Vend 1.

Special Vend 1 Vend Price 1 (SP1 11)

Setting vend price for Normal Hot in Special Vend 1.

Special Vend 1 Vend Price 6 (SP1 16)

Setting vend price for Perm Press Cold in Special Vend 1.

Special Vend 1 Wash Status Agitate Steps Subtracted Minutes (SP1 21)

Special Vend 2 Days Enable (SP2)

How to Program Cycle Modifier MEDIUM Key #1 Options (CNP 2)

How to Program Cycle Modifier MEDIUM Additional Extra Rinse Time (CNP 5)

Cycle Parameters (CYCP-)

Setting time for various steps in each cycle type.

Low Power-Auto Shutdown 3 Days Enable (LPAS 3)

IR Access (IrA En)

Lucky Cycle (LUC-)

Programmable Push Start Display (PPSt d)

OPL Delayed Start (OPL 2)

Out of Order (oUt)

Daylight Savings Programming

Programming options for daylight savings time.

Low Power/Auto Shutdown Options

Settings for low power and auto shutdown features.

Manual Diagnostics and Factory Test

Enabling/disabling manual diagnostics and factory test.

Vend Price 2 (AtS 2)

Setting vend price for Normal Warm cycle.

Vend Price 6 (AtS 6)

Setting vend price for Perm Press Cold cycle.

Cycle Modifier Key 1 Medium Vend Price Adder (ACNP 1)

Coin 2 Value (dEn 2)

Card Reader Display Control (CArd)

Error Code Programming (Error-)

Turning on or off certain error codes in the control.

Slow Drain Detection Error Menu

Set Daylight Savings Time (dLS-)

Special Vend 1 Start Hour (SP1 3)

Setting the start hour for Special Vend 1.

Special Vend 1 Length in Hours (SP1 7)

Setting the duration in hours for Special Vend 1.

Special Vend 1 Vend Price 2 (SP1 12)

Setting vend price for Normal Warm in Special Vend 1.

Special Vend 1 Vend Price 7 (SP1 17)

Setting vend price for Delicates Hot in Special Vend 1.

Special Vend 1 Cycle Modifier Default Value (SP1 22)

Special Vend 3 Days Enable (SP3)

How to Program Cycle Modifier HEAVY Key #2 Options (CNP 3)

How to Program Cycle Modifier HEAVY Additional Wash Time (CNP 6)

Low Power-Auto Shutdown 1 Days Enable (LPAS 1)

Low Power-Auto Shutdown 4 Days Enable (LPAS 4)

Manual Rapid Advance (rAPdEn)

Water Temperature Indicator (tP ind)

Programmable Open Lid Display (PodL d)

OPL Display Power Save (OPL 3)

Lucky Cycle Options

Vend Price 3 (AtS 3)

Setting vend price for Normal Cold cycle.

Vend Price 7 (AtS 7)

Setting vend price for Delicates Hot cycle.

Cycle Modifier Key 2 HEAVY Vend Price Adder (ACNP 2)

Start Pulse Value (PLSE)

Audio Signal (AUdio)

Overflow Mode Display

Special Vend 1 Days Enable (SP1 1)

Enabling or disabling days for Special Vend 1.

Special Vend 1 Start Date (SP1 4)

Setting the start date for Special Vend 1.

Special Vend 1 End Date (SP1 8)

Setting the end date for Special Vend 1.

Special Vend 1 Vend Price 3 (SP1 13)

Setting vend price for Normal Cold in Special Vend 1.

Special Vend 1 Vend Price 8 (SP1 18)

Setting vend price for Delicates Warm in Special Vend 1.

Special Vend 1 Cycle Modifier MEDIUM Key #1 Vend Price (SP1 23)

Special Vend 4 Days Enable (SP4)

How to Program Cycle Modifier MEDIUM Additional Wash Time (CNP 4)

How to Program Cycle Modifier HEAVY Additional Extra Rinse Time (CNP 7)

Low Power-Auto Shutdown 2 Days Enable (LPAS 2)

Power Fail Reset (PF rSt)

Setting time to store active cycle info during power failure.

Manual Diagnostics (d1A9En)

Programmable Close Lid Display (PCdL)

Vend Price Display Override (AtS do)

Drop Off Mode (droP)

OPL Parameters

Vend Price 4 (AtS 4)

Setting vend price for Perm Press Hot cycle.

Vend Price 8 (AtS 8)

Setting vend price for Delicates Warm cycle.

Vend Price Decimal Point (AtS dP)

Start Pulse Mode (PLSNod)

How to Program the Audio Signal

Allow Error Clearing

Special Vend 1 Start Month (SP1 5)

Setting the start month for Special Vend 1.

Special Vend 1 End Month (SP1 9)

Setting the end month for Special Vend 1.

Special Vend 1 Vend Price 4 (SP1 14)

Setting vend price for Perm Press Hot in Special Vend 1.

Special Vend 1 Vend Price 9 (SP1 19)

Setting vend price for Delicates Cold in Special Vend 1.

Special Vend 1 Cycle Modifier HEAVY Vend Price (SP1 24)

How to Program Default Cycle Modifier (CNP 1)

Factory Test (Ft En)

OPL Parameters (OPL-)

Special Vend 1 End Year (SP1 10)

Setting the end year for Special Vend 1.

Special Vend 1 Vend Price 5 (SP1 15)

Setting vend price for Perm Press Warm in Special Vend 1.

Special Vend 1 Wash Status Agitate Steps Added Minutes (SP1 20)

Special Vend 1 Cycle Modifier MEDIUM Key #1 Options (SP1 25)

OPL Mode Enable (OPL 1)

Special Vend 1 Cycle Modifier HEAVY Key #2 Options (SP1 26)

Testing Machine and Electronic Control Functions (continued)

Diagnostic Test Options

Diagnostic Test Descriptions

Diagnostic Test Descriptions (continued)

Factory Test

To Enter Factory Test

Factory Test Cycle Quick Reference Chart

Error Codes (continued)

No Card Reader Initialization (EC 11)

Product Byte #1 Mis-Match (En 31)

No Water Flow Error (EnFLO)

No Communication (EC 18)

Cannot Communicate with the Machine ID Control (En 3F)

Overflow Error (E oF)

Network Communication Error

Drain Error (E dr)

Pressure Sensor Error (E P5)

Break-in Alarm Error

Slow Drain Error (E Sd)

Thermal Protect Error (E EP)