Allied 595 - Torque Specifications

Loader Specification Sheet
(PER ASAE S301.2)
MODEL NUMBER: 595
MOUNTING HEIGHT: 36.0” (NOMINAL)
TYPICAL RANGE: 33.0” TO 39.0”
CYLINDER SPECIFICATIONS [INCHES]
CYLINDER
BORE
ROD STROKE
BUCKET
3.00 1.50
20.63
LIFTING
3.00
1.75
28.50
LEVELING
3.50 1.75
12.00
TSL BKT
3.00 1.75
22.00
A) MAXIMUM UFT HEIGHT (FULL HEIGHT): 139.4” (11.6’)
B) CLEARANCE WITH BUCKET DUMPED (FULL HEIGHT): 108.3” (9.0')
C) REACH AT FULL HEIGHT: 32”
D) MAXIMUM DUMP ANGLE (FULL HEIGHT): 41.0*
D) TSL MAX DUMP ANGLE: 65.0’
D1) TSL DUMP ANGLE AT GROUND: 90*
F) BUCKET ROLLBACK ANGLE (GROUND): 18'
FI) TSL BUCKET ROLLBACK ANGLE: 35’
G) DIGGING DEPTH: 5.5
H) OVERALL HEIGHT IN CARRY POSITION: 79.0” (6.6')
R) ROLL8ACK ANGLE AT FULL HEIGHT: 101.0*
R) TSL BUCKET ROLLBACK ANGLE AT FULL UFT: 49.5*
ESTIMATED BREAKOUT FORCE: 4205 LBS
ESTIMATED LIFT CAPACITY: 2430 LBS
NOTES:
I) CALCULATED VALUES ASSUME 2500 PSI CYLINDER PRESSURE
2) 8REAKOUT FORCE ESTIMATED AS PER ASAE S301.2-4.1.2.
(NET PAYLOAD APPLIED AT CUTTING EDGE)
3) LIFT CAPACITY ESTIMATED AS PER ASAE S301.2-4.1.1.
(PAYLOAD APPLIED AT BUCKET MIDPOINT)
4) ALL PINS ARE 1.25 DIAMETER
Torque Specifications
Recommended Torque in Foot Pounds (ft-lbs) & Newton Meters (NM)*
Metric
Bolt
Dia.
(mm)
Wrench
Size
(mm)
Bolt Head |
O
Q
O
Class 4.6
(ft-lbs) (NM)
Class 8.8
(ft-lbs) (NM)
Class 9.8
(ft-lbs) (NM)
n
13
7.3 10
21.1
29
H
16
14.5
20
42
57
12
18
25
34
74 100
73
99
14 21
40
54 118
160
116
157
16
24
62
84
167 226 181
245
20
30
122 165
325
440
22 33
443
600
24 36
211
286
563
763
27
41
821 1112
ill
46
418
566 1119
1516
St sand a
rd
Bolt Diameter
(inches)
Wrench
Size
(inches)
Bolt Head
O 0
H
Grade 2
(ft-lbs) (NM)
Grade 5
(ft-lbs) (NM)
0.250
1/4
7/16
6
7
8
11 12
16
0.313
5/16
1/2 11
15
17
23
25
33
0.375
3/8
9/16
20
27
31
42 44
60
0.438
7/16
5/8
32
43
49 66
70
95
0.500
1/2
3/4
49
66
76
103
106
144
0.563
9/16
7/8
70
95
109 148
153
207
0.625
5/8
15/16
97
131
150
203
212
287
0.750
3/4
1 1/8
144
195
266
360 376
509
0.875
7/8
1 5/16
166
225
430 583
606
821
1.000 1
1 1/2
250
339
644
873 909 1232
1.125
1 1/8
1 11/16
354
480
795
1077
1288 1745
1.250
1 1/4
1 7/8
500
678
1120
1518 1817 2462
1.375
1 3/8
2 1/16
655
887
1470
1992 2382 3228
1.500
1 1/2
2 1/4
870
1179
1950
2642
3161 4283
*Use 80% of the specified torque value for plated or lubricated fasteners.
2