Alpine CDE-133BT User Manual

16-EN
Adjusting Subwoofer Level/Bass Level/
Middle Level/Treble Level/Balance (Between
Left and Right)/Fader (Between Front and
Rear)/Loudness/Defeat
1 Press AUDIOSETUP repeatedly to choose the desired
mode.
Each press changes the mode as follows:
SUBWOOFER
*1
 BASS LEVEL
*2
 MID LEVEL
*2
 TRE LEVEL
*2

BALANCE  FADER  LOUDNESS
*2/*3
 DEFEAT  VOLUME 
SUBWOOFER
*1 When the subwoofer mode is set to OFF, its level cannot be
adjusted.
*2 Adjustable only when DEFEAT is OFF.
*3 For details about loudness, refer to “Turning Loudness On/Off ”
on page 17.
Note
• If no operation is performed for 5 seconds, the unit automatically
returns to normal mode.
2 Turn the Rotary encoder until the desired sound is
obtained in each mode.
By setting DEFEAT ON, previously adjusted settings of BASS,
MID, TRE LEVEL and LOUDNESS will return to the factory
defaults.
Audio Setup
You can flexibly customize the unit to suit your own preference and
usage. From the AUDIO SETUP menu, Audio Setting can be modified.
1 Press and hold AUDIOSETUP for at least 2 seconds to
activate the SETUP mode.
2 Turn the Rotary encoder to select AUDIO, and then press
ENTER.
AUDIO  GENERAL  DISPLAY  TUNER  iPod 
BLUETOOTH
*1
*1 CDE-133BT only.
3 Turn the Rotary encoder to select the desired sound
setting menu, and then press ENTER.
FAC TORY EQ
*2/*3
 LOUDNESS
*2
 3BAND EQ
*2/*4
 VOL LV ADJ
 HPF
*2
 SUBWOOFER  SUBW LPF
*2/*5
 SUBW PHASE
*5

SUBW SYS
*5
 POWER IC
(e.g. Select SUBWOOFER)
*2 Adjustment cannot be performed when DEFEAT is set to ON.
*3 The FACTORY EQ’s setting value and 3BAND EQ’s setting
value are linkage.
*4 The FACTORY EQ’s setting value and 3BAND EQ’s setting
value are linkage. In step 3, three sound adjustment items (Bass,
Mid and Treble) can be selected in 3BAND EQ mode, turn the
Rotary encoder to select the desired item, and then press
ENTER to continue to step 4.
*5 These functions are inoperable when Subwoofer is set to OFF.
4 Turn the Rotary encoder to change the setting, and then
press ENTER.
(e.g. Select SUBW ON or SUBW OFF)
5 Press and hold AUDIOSETUP for at least 2 seconds to
return to normal mode.
Notes
•Pressing  returns to the previous Sound menu mode.
• Pressing and holding  for at least 2 seconds will return to normal
mode.
• If no operation is performed for 60 seconds, Sound menu mode is
cancelled.
10 typical equalizer settings are preset at the factory for a variety of
musical source material.
 Setting item: FACTORY EQ
Setting contents:
USER / FLAT (Initial setting) / POPS / ROCK / NEWS / JAZZ /
ELEC DANCE / HIP HOP / EASY LIS / COUNTRY / CLASSICAL
Sound Setting
Subwoofer +0 ~ +15
Bass level -7 ~ +7
Middle level -7 ~ +7
Treble level -7 ~ +7
Balance L15 ~ R15
Fader R15 ~ F15
Loudness ON/OFF
Defeat ON/OFF
Volume 0 ~ 35
AUDIO/SETUP
Rotary encoder
/ENTER

Use steps 1 to 5 to select one of the setting modes to modify.
See the applicable section below for details about the
selected setting item.
Equalizer Presets (F-EQ)

Alpine CDE-133BT Specifications

General

MP3 playback	No
CD-R playback	Yes
Playback disc formats	CD audio
Audio formats supported	MP3
FM band range	87.5 - 108 MHz
LW band range	153 - 281 kHz
Supported radio bands	FM, LW, MW
Preset stations quantity	18
RDS features	TA, TP
Product color	Black
CD changer capacity	1 discs
Disc types supported	CD, CD-R, CD-RW
Audio output channels	4.0 channels
Equalizer bands quantity	7
Signal-to-Noise Ratio (SNR)	105 dB
Display type	LCD
Bluetooth version	3.0+HS
Bluetooth profiles	A2DP, AVRCP, HFP, HSP
Headphone connectivity	3.5mm
Apple docking compatibility	iPhone, iPod
RMS rated power	200 W
File format system	FAT32
Power requirements	14.4V DC, 11-16V
Operating temperature (T-T)	-10 - 60 °C

Weight and Dimensions

Weight	1500 g
Dimensions (WxDxH)	178 x 161 x 50 mm