EasyManuals Logo

Alpine CDE-133BT User Manual

Alpine CDE-133BT
41 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #9 background imageLoading...
Page #9 background image
9-EN
Accessory List
Head Unit ..................................................................................1
Power Cable ..............................................................................1
Microphone (CDE-133BT only)................................................1
Mounting Sleeve ......................................................................1
Carrying Case............................................................................1
Rubber Cap ...............................................................................1
Hex Bolt.....................................................................................1
Screw (M5 × 8) ..........................................................................4
Owner’s Manual..................................................................1 set
Turning Power On and Off
Press SOURCE to turn on the unit.
Note
The unit can be turned on by pressing any other button except and
e (Release).
Press and hold SOURCE for at least 2 seconds to turn
off the unit.
Note
The first time power is turned on, the volume will start from level 12.
Source Selection
Press SOURCE to change the source.
TUNER DISC USB AUDIO/iPod
*1
BT AUDIO
*2
AUXILIARY
*3
TUNER
*1 Only when the iPod/iPhone is connected.
*2 Only for CDE-133BT.
Only when BT AUDIO is set to ON. Refer to “Setting the
BLUETOOTH Connection (BT IN)” on page 24.
*3 Only when AUX SETUP is set to ON. Refer to “Setting the AUX
SETUP Mode” on page 21.
Detaching and Attaching the Front Panel
1
Turn off the unit power.
2
Press e (Release) at the lower left side until the front
panel pops out.
3
Grasp the left side of the front panel and pull it out.
Notes
The front panel may become hot in normal usage (especially the
connector terminals on the back of the front panel). This is not a
malfunction.
To protect the front panel, place it in the supplied carrying case.
When detaching the front panel, do not apply excessive force as it may
result in malfunction.
1
Insert the right side of the front panel into the main unit.
Align the groove on the front panel with the projections
on the main unit.
2
Push the left side of the front panel until it locks firmly into
the main unit.
Notes
Before attaching the front panel, make sure that there is no dirt or dust
on the connector terminals and no foreign object between the front
panel and the main unit.
Attach the front panel carefully, holding the sides of the front panel to
avoid pushing buttons by mistake.
Initial System Start-Up
Be sure to press the RESET button when using the unit for the first time,
after changing the car battery, etc.
1
Turn off the unit power.
2
Remove the detachable front panel.
Getting Started
SOURCE/
AUDIO/SETUP
Rotary encoder
/ENTER
Detaching
Attaching

Table of Contents

Other manuals for Alpine CDE-133BT

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Alpine CDE-133BT and is the answer not in the manual?

Alpine CDE-133BT Specifications

General IconGeneral
MP3 playbackNo
CD-R playbackYes
Playback disc formatsCD audio
Audio formats supportedMP3
FM band range87.5 - 108 MHz
LW band range153 - 281 kHz
Supported radio bandsFM, LW, MW
Preset stations quantity18
RDS featuresTA, TP
Product colorBlack
CD changer capacity1 discs
Disc types supportedCD, CD-R, CD-RW
Audio output channels4.0 channels
Equalizer bands quantity7
Signal-to-Noise Ratio (SNR)105 dB
Display typeLCD
Bluetooth version3.0+HS
Bluetooth profilesA2DP, AVRCP, HFP, HSP
Headphone connectivity3.5mm
Apple docking compatibilityiPhone, iPod
RMS rated power200 W
File format systemFAT32
Power requirements14.4V DC, 11-16V
Operating temperature (T-T)-10 - 60 °C
Weight and Dimensions IconWeight and Dimensions
Weight1500 g
Dimensions (WxDxH)178 x 161 x 50 mm

Related product manuals