To Next PageTo Next PageHow to fix an Alpine PSS-22WRA that will not turn on?
If your Alpine Car Receiver system isn't turning on, it could be due to a missing or blown fuse at the battery. In this case, insert or replace the fuse. Another possible cause is that the radio's Remote Turn-On wire may be disconnected. To solve this, verify that the Remote Turn-On wire is properly connected.
Why is the volume so loud on my Alpine PSS-22WRA with an aftermarket headunit?
If the volume is too loud with an aftermarket headunit in your Alpine Car Receiver, it might be because the speaker level out is connected at the T-Harness. To fix this, ensure that the low level RCA adapters are used in the aftermarket headunit system. Also, the amplifier's gain control might not be properly adjusted. Refer to the corresponding system diagram to adjust it correctly.
What to do if the airbag light is on after installing an Alpine PSS-22WRA?
If the airbag light is on after working on your vehicle with the Alpine Car Receiver, it may be because you failed to disconnect the battery. Disconnect the battery and reconnect it after 5 minutes. If the problem persists, take the vehicle to a Jeep dealer.
Why does my Alpine PSS-22WRA Car Receiver subwoofer sound so low?
If the subwoofer sounds very low in your Alpine Car Receiver setup, the gain level may be set to the lowest setting. Adjust the level to the recommended setting. Also, the audio phase may be reversed, so ensure that the PHASE is set to 0.
Why does my Alpine PSS-22WRA only turn on with the radio source?
If your Alpine Car Receiver system only turns on when using the radio source, the aftermarket Power Antenna wire may be connected to the amp. To resolve this, connect the Remote Turn-On wire (Blue/White) to the Blue wire on the amplifier harness.
What to do if one of the speakers has no sound on my Alpine PSS-22WRA?
If one of the speakers in your Alpine Car Receiver system has no sound, it could be due to a disconnected pin or loose connection. Check all connections to the speaker, looking for loose pins or disconnected terminals.
General| Brand | Alpine |
|---|---|
| Model | PSS-22WRA |
| Category | Car Receiver |
| Language | English |
General guidelines for safe use and installation, emphasizing reading manuals and understanding symbols.
Explanation of symbols indicating potential death, serious injury, or property damage from incorrect product use.
Indicates actions that are forbidden or must not be performed during installation or use.
Indicates actions that are mandatory or must be performed for safe operation.
Covers warnings related to disassembly, storage of small parts, fuse replacement, and airbag proximity.
Details cautions regarding product connection, cord routing, vent blocking, and accessory usage.
Step-by-step instructions for removing the factory radio unit from the vehicle.
Procedure for removing the factory top dash tweeters for 2011-2014 models.
Procedure for removing factory top dash speakers for 2015-2018 models.
Detailed steps for removing the front lower dash speakers on both driver and passenger sides.
Instructions for removing the center console shifter panel using a panel removal tool.
Procedure for removing sound bar speakers for 2011-2014 Jeep Wrangler models.
Procedure for removing sound bar speakers for 2015-2018 Jeep Wrangler models.
Steps to remove the passenger side seat using 18mm socket and T45 Torx bolt.
Guide for installing front tweeters in 2011-2014 models, including crossover connection.
Guide for installing front tweeters in 2015-2018 models, using tweeter adapters.
Procedure for installing front woofers, including polyfill and foam strip placement.
Steps for installing rear sound bar tweeters and woofers for 2011-2014 models.
Procedure for installing rear sound bar tweeters and woofers for 2015-2018 models.
Diagram illustrating wiring connections for the PSS-22WRA system with a factory headunit.
Wiring diagram for PSS-22WRA with Alpine Restyle headunit, including recommended sound settings.
Wiring diagram for PSS-22WRA with an aftermarket headunit, showing connections and settings.
