AMCI SMD17E2 - Page 5

20 Gear Drive, Plymouth Ind. Park, Terryville, CT 06786
Tel: (860) 585-1254 Fax: (860) 584-1973 http://www.amci.com
SMD17E2 User Manual TABLE OF CONTENTS
5
Task 1: Installing the SMD17E2
Location ................................................... 85
IP50 Rated Units ............................ 85
IP64 Rated Units ............................ 85
Prevent Electrostatic Damage ........ 85
Prevent Debris From 
Entering the Unit ......................... 85
Remove Power Before Servicing .. 85
Operating Temperature Guidelines .......... 86
Mounting .................................................. 86
SMD17E2-M12 Mounting ............ 86
SMD17E2-M12S Mounting .......... 86
SMD17E2-60 Outline Drawing ..... 87
SMD17E2-80 Outline Drawing ..... 88
Connecting the Load ...................... 88
Power and Input Connector ..................... 89
Compatible Connectors
and Cordsets .................................. 89
Power Wiring ........................................... 90
Input Wiring ............................................. 91
Cable Shields ................................. 91
Sinking Sensors Require a 
Pull Up Resistor .......................... 91
Network Connectors ................................ 92
Compatible Connectors 
and Cordsets ................................ 92
TIA/EIA-568 Color Codes ............ 92
EtherNet/IP Connections ......................... 93
Non-DLR Applications ................. 93
DLR Applications .......................... 93
Modbus TCP Connections ....................... 93
PROFINET Connections ......................... 93
Non-MRP Applications ................. 93
MRP Applications ......................... 93
Task 2: Set the IP Address and 
Protocol
Determine the Best Method for 
Setting the IP Address ........................... 95
Use Factory Default Settings ................... 95
Use the Embedded Web Server ............... 96
Use the AMCI NET Configurator 
Utility ..................................................... 98
Task 3: Implicit Communications
with an EDS
Obtain the EDS file .................................. 103
Install the EDS file ................................... 103
Start the EDS Hardware 
Installation Tool .......................... 103
Install the EDS File ....................... 104
Task 3: Implicit Communications
with an EDS (continued)
Host System Configuration ...................... 106
Add the SMD17E2 to Your Project ......... 106
Configure the SMD17E2 Driver .............. 107
General Tab ................................... 107
Connection Tab ............................. 107
Configuration Tab ......................... 107
Buffering the I/O Data ............................. 108
Task 4: Implicit Communications
Without an EDS
Host System Configuration ...................... 109
Add the SMD17E2 ................................... 109
Configure the SMD17E2 .......................... 111
Buffer I/O Data ........................................ 112
Task 5: EtherNet/IP Explicit 
Messaging
Required Message Instructions ................ 113
Create Four New Data Files. .................... 113
Add the Message Instructions 
to your Ladder Logic .............................. 114
Troubleshooting ....................................... 117
Task 6: Modbus TCP Configuration
Enable Modbus TCP Protocol .................. 119
Modbus Addressing ................................. 119
Modbus Table Mapping ................ 119
Host Addressing ............................ 119
AMCI Modbus TCP Memory Layout ...... 120
Supported Modbus Functions .................. 121
Supported Modbus Exceptions ................ 121
Task 7: PROFINET Network 
Configuration
Basic Steps ............................................... 123
Download the GSDML files .................... 123
GSDML File Installation .......................... 123
Configure the PROFINET Network ......... 123
Add the SMD17E2 to the 
PROFINET Network .............................. 124
Set the I/O Configuration ......................... 126
Verify and Download the 
New Configuration ................................. 127
MRP Installations ..................................... 127
Configure the SMD17E2 as an MRC ....... 127