American Standard 2881 User Manual

Plumbers' Putty or CaulkingAdjustable Wrench Phillips ScrewdriverChannel Locks
TOOLS REQUIRED
SPREAD
LAVATORY
FAUCET
Installation
Instructions
M968211
Certified to comply with ANSI A112.18.1M
1
SPOUT ASSEMBLY
4
2
6
1
3
VALVE INSTALLATION
2
5/16'' MIN.
Insert VALVE BODY (1) through hole from underside
of SINK (2). Threads of VALVE BODY (1) should extend
at least 5/16 inch above SINK (2) top. If necessary,
adjust LOCKNUT (3). Make sure RUBBER WASHER (6)
is installed.
Place RUBBER RING (4) on SINK (2) and screw DECK
ADAPTER (5) onto VALVE BODY (1) until snug against
internal stop.
Set VALVE BODIES (1,1A) so that their outlets are
facing toward center of sink and then tighten LOCKNUT
(3) using WRENCH (7) supplied with faucet.
7
3
TEE AND HOSE INSTALLATION
2881
Thank you for selecting American-Standard...the benchmark of fine
quality for over 100 years.
To ensure that your installation proceeds smoothly--please read these
instructions carefully before you begin.
Connect TEE (1) to SPOUT SHANK (2). Tighten COUPLING
NUT (3).
Connect COUPLING NUTS (4) of HOSE to each valve outlet and
tighten securely.
1
3
2
4
HOSE
Insert SPOUT SHANK (1) through center
hole of SINK (2). Make sure RING
WASHER (3) is properly positioned
into SPOUT BASE.
Assemble RUBBER WASHER (4),
BRASS WASHER (5) and LOCKNUT (6)
onto threads of SPOUT SHANK (1)
from underside of SINK (2).
Insert LIFT ROD (7) through SPOUT (8)
and slot of BRASS WASHER (5).
Align SPOUT (8) and tighten LOCKNUT (6).
Be sure slot in BRASS WASHER (5) is
positioned to the rear as shown.
7
8
1
3
4
6
5
SLOT
2
5
Turn off hot and cold water supplies before beginning.
CAUTION
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 (800) 223-0068
Weekdays 8:00 a.m. to 8:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
Product names listed herein are trademarks of American Standard Inc.
© American Standard Inc. 2002
by
COLLECTION
™
“”
THE
VALVE
OUTLET

American Standard 2881 Specifications

General

Brand	American Standard
Model	2881
Category	Plumbing Product
Language	English

Summary

Spout Assembly and Valve Installation

Spout Assembly Caution

Turn off hot and cold water supplies before beginning the spout installation.

Spout Shank Insertion

Insert spout shank through the center hole of the sink and position the ring washer.

Rubber Washer and Locknut Assembly

Assemble rubber washer, brass washer, and locknut onto the spout shank.

Lift Rod and Spout Alignment

Insert lift rod through spout and align spout, ensuring proper locknut tightening.

Valve Body Installation

Insert valve body through sink hole, ensuring correct height and rubber washer installation.

Deck Adapter and Valve Body Positioning

Install rubber ring and deck adapter, then position valve bodies for sink center.

Water Supply and Handle Installation

Water Supply Connections

Connect water supply to faucet using flexible supplies or bull-nose risers.

Handle Installation Steps

Install adapter, handle base, handle, and secure with screw and index cap.

Testing Installed Fitting

Turn on water, remove aerator, flush lines, and replace aerator to test.

Pop-Up Drain Installation and Service

Pop-Up Drain Assembly

Assemble tailpiece, drain body, locknut, washer, and gasket for pop-up drain.

Drain Body Mounting

Apply putty, feed drain body through sink, and thread flange onto body.

Pivot Rod and Extension Rod Setup

Assemble and connect pivot rod to drain body and extension rod.

Drain Stopper Adjustment

Insert stopper, adjust height, and check for seal and leaks.

Handle Rotation Service

Procedure to change handle rotation direction by adjusting stop washer.

Care Instructions

Rinse with water and dry with soft cloth; avoid harsh cleaners.