EasyManuals Logo

Ampeg SVT-3 PRO User Manual

Ampeg SVT-3 PRO
16 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #6 background imageLoading...
Page #6 background image
SVT-3 PRO Bass Guitar Amplifier
6
11. TREBLE: Use this to adjust the high
frequency level of the amplifier. This
provides up to 14 dB of boost, or 19
dB of cut at 5 kHz. The high frequency
output is flat at the center position.
12. MASTER: Use this to control the
overall output level. Use it wisely and
turn it down when making connections
or trying something new.
13. TUBE GAIN: The tube gain control
varies the high voltage supply to the
preamp tubes. This allows a variety of
tonal response characteristics from
the power amp and replaces the limiter
found on typical solid state power amps.
At “10” the voltage is at maximum,
providing a dynamic, highly responsive
tone. At “0” the voltage is at minimum,
offering a thickened, more compressed
tone. This tone may also be distorted,
depending on volume level. In between
settings are best for preventing harsh
distortion when driving the power amp
to its limits. The effect of this control
increases from moderate to dramatic
as the power amp is driven harder.
NOTE: When adjusting the tube gain control
from “10” to “0” rapidly, a low frequency
hum and muting of the output signal
occur simultaneously. This is due to
shifting of the DC bias point of the tubes
and is no cause for concern. Adjusting
the control quickly from “0” to “10”
brings a moderate delay due to the
power supply capacitors charging.
14. MUTE: Press this switch in to mute
all outputs except the tuner out. The
footswitch may also control muting if
the mute switch on the front panel is
left in the “out” position. (The front panel
switch is still active with the footswitch
connected. This is excellent for tuning
your bass with an electric tuner without
having to adjust any levels to turn down
the sound). The peak/mute LED will
illuminate when this switch is engaged.
15. GRAPHIC EQ: When this switch is
engaged, the 9-band graphic EQ is
enabled. A footswitch overrides this
switch.
The Front Panel continued
0
+12dB
-12dB
LEVEL
+8dB
-10dB
MUTE
EQ
PEAK /
MUTE
BRT
-15dB
HI
LO
zHk9zH33 5kHz2kHz900Hz600Hz300Hz150Hz80Hz
ON
POWER
ON
MASTER TUBE GAINTREBLEFREQUENCYMIDRANGEBASSGAININPUT
1 4 16 19 205 8 9 11 12 181713102 3 6 7 14 15

Other manuals for Ampeg SVT-3 PRO

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Ampeg SVT-3 PRO and is the answer not in the manual?

Ampeg SVT-3 PRO Specifications

Power IconPower
output power rating at 4 ohm load450 Watts RMS
output power rating at 8 ohm load275 Watts RMS
power requirements domestic120VAC, 60Hz
power requirements export230VAC, 50/60Hz
power requirements Japan100V 50/60Hz
Tone Control IconTone Control
bass control range±12dB @ 50Hz
midrange control range±15dB @ selected by Frequency control
treble control range+14dB/-19dB @ 5kHz
Graphic Equalizer IconGraphic Equalizer
graphic EQ level±10dB
graphic EQ range 33Hz±15dB
graphic EQ range 80Hz±8dB
graphic EQ range 150Hz±8dB
graphic EQ range 300Hz±8dB
graphic EQ range 600Hz±8dB
graphic EQ range 900Hz±8dB
graphic EQ range 2kHz±8dB
graphic EQ range 5kHz±9dB
graphic EQ range 8kHz±10dB
Switches IconSwitches
bright switch+6dB @2kHz
ultra high switch+6dB @ 5kHz
ultra low switch+2.5dB @ 50Hz -12dB @ 560Hz +1.5dB @ 5kHz
Physical Characteristics IconPhysical Characteristics
dimensions width19/17.4”
dimensions height4” (with feet)
dimensions depth15.5”

Related product manuals