Anest Iwata Wider 1 - User Manual

1
INSTRUCTION MANUAL
Spray Gun
Be sure to observe warning s and cautions in this instruction manual.
If not, it can cause paint ejection and serious bodily injury by drawing organic solvent.
Be sure to observe following marked items which are especially important
. 
Indicates a potentially hazardous situation which, if not avoided, may result in serious injury or loss of
life.
Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury
or property damage.
Indicates notes which we ask you to observe. The safety precautions in this instruction manual are
the minimum necessary conditions. Follow national and local regulations regarding fire prevention,
electricity and safety as well as your own company regulations.
Symbol Marking on the Spray Gun:
II 2 G Ex h X
This ANEST IWATA spray gun
complies with 2014/34/EU Directive
relating to equipment and protective
systems intended for use in explosive
potentially atmospheres.
II 2 G Ex h IIB T6 Gb X
T
Amb
+5°C +40°C
Complies
with
European
Directive
Specific
Marking for
Explosion
Protective
Group II
(Surface)
Category
(Zone 1&2)
Type of
Atmosphere
(GAS)
Ignition
Protection
(not applied)
Explosion
Group
(Ethylene)
Temperature
Class
( 85°C)
Explosion
Protection
level
(EPL)
Additional
conditions:
Ambient
Temperature
Any static Electricity should be
discharged and needs to be
diverted to the ground via a
conductive air hose not
included.
Important specifications
Max. Pressure 0.70MPa / 7.0bar / 100psi
Noise level 79dB(A)
Spray condition Recommended
Measuring point 1m backwards from spray gun, 1.6m height
Max. temperature Atmosphere: 5°C ~40°C (41°F~104°F) Air and Fluid: 5°C ~43°C (41°F~109°F)
Important
Never connect pressure feeding paint except pressure feed type spray gun.
*1. Atomizing air pressure means air pressure at spray gun inlet when trigger is pulled and air flows.
Nozzle needle assy combination
Fluid nozzle Fluid needle
Orifice  mm (in) Mark Mark
 0.8 (0.031) / W1 / 08
08H WIDER1
 1.0 (0.039) / W1 / 10
 1.3 (0.051) / W1 / 13
13 WIDER1
 1.5 (0.059) / W1 / 15
 1.8 (0.071) / W1 / 18 18 WIDER1
Main specifications
Model Type of feed
Nozzle orifice
 mm (in)
Air cap assy
Mark
Recommended condition
Air consumption
l/min (cfm)
Pattern width
mm (in)
Air & fluid
connection
Mass
g (lbs.)
*1 Atomizing air
pressure
MPa (bar / PSI)
Fluid output
ml/min
WIDER1
-
08E2P
Pressure
0.8
(0.031)
E2P
0.29
(3.0 / 43)
150
270 (9.5)
190 (7.5)
Air
G1/4
(NPS1/4)
Fluid
G1/4
(NPS1/4)
290
(0.64)
-
10E2P
1.0
(0.039)
200
220 (8.7)
-
13E2P
1.3 (0.051)
0.24
(2.5 / 36)
220 (7.8)
210 (8.3)
-
15E2P
1.5 (0.059)
250
240 (9.4)
WIDER1
-
10E1S
Suction
1.0 (0.039)
E1
85
75 (2.6)
120 (4.7)
-
13K1S
1.3 (0.051)
K1
150
145 (5.1)
155 (6.1)
-
13H2S
H2
225 (7.9)
160 (6.3)
-
13H4S
H4
0.2 (2.0 / 28)
140
210 (7.4)
180 (7.1)
-
15K1S
1.5 (0.059)
K1
0.24
(2.5 / 36)
175
145 (5.1)
170 (6.7)
-
15H2S
H2
170
225 (7.9)
175 (6.9)
-
18N1S
1.8 (0.071)
N1
210
170 (6.0)
170 (6.7)
WIDER1
-
10E1G
Gravity
1.0 (0.039)
E1
95
75 (2.6)
130 (5.1)
-
13K1G
1.3 (0.051)
K1
160
145 (5.1)
170 (6.7)
-
13H2G
H2
225
(7.9)
175 (6.9)
-
13H4G
H4
0.2 (2.0 / 28)
155
210 (7.4)
205 (8.1)
-
15K1G
1.5 (0.059)
K1
0.24
(2.5 / 36)
200
145 (5.1)
180 (7.1)
-
15H2G
H2
190
225 (7.9)
190 (7.5)
-
18N1G
1.8 (0.071)
N1
240
170 (6.0)
This manual contains IMPORTANT
WARNINGS and INSTRUCTIONS.
Equipment in this manual is exclusively for
painting purposes.
Do not use for other purposes.
The operator shall be fully conversant with
the requirements stated in this instruction
manual including important warnings,
cautions and operation and correct handling.
Read and understand the instruction
manual, before use and retain for reference.
IMPORTANT WARNING: Our spray guns, airbrushes, and other products are made to conform by our local group companies with local
laws and regulations
that may differ from place to place. Improper trade of products outside of designated domestic territories (unauthorized reselling) can result in legal violations,
local fines, and penalties. ANEST IWATA CORPORATION assumes no liability for products acquired through unauthorized reselling and in such cases and due
to quality control protocols, unauthorized reselling renders the warranty null and void.

Summary

Important Specifications

Max. Pressure

Maximum operating pressure limit.

Noise Level

Measured noise level of the equipment.

Spray Condition

Conditions related to spray application.

Measuring Point

Designated point for measurements.

Max. Temperature

Maximum permissible operating temperature.

Safety Precautions

Fire and Explosion Hazards

Risks associated with fire and explosions.

Improper Use of Equipment

Dangers arising from incorrect usage.

Protection of Human Body

Measures to protect user's health and safety.

Other Precautions

Additional safety guidelines to follow.

How to Connect

Connection Step-by-step Procedure

Detailed steps for connecting the spray gun.

Maintenance and Inspection

Maintenance Step-by-step Procedure

Detailed steps for maintenance and inspection.

Inspection Points

Key areas requiring inspection.

Parts Replacement Standard

Criteria for replacing parts.

Troubleshooting

Spray Pattern Issues

Common problems with spray patterns.

Operating Guidance

How to operate the spray gun correctly.

Residual Risk

Residual Risk Definitions

Definitions of DANGER, WARNING, and CAUTION.

Risk Not Identified on Machine

Risks not specifically marked on the equipment.

List of Residual Risks

Risk Classification and Description

Classified residual risks and their descriptions.

Risk Mitigation Measures

Protective measures for identified risks.

Anest Iwata Wider 1 Specifications

General

Air Pressure	2.0 bar (29 psi)
Cup Capacity	600 ml
Recommended Air Pressure	2.0 bar (29 psi)
Type	Gravity Feed
Nozzle Size	1.3 mm
Fluid Output	160 ml/min
Air Inlet Size	1/4"